To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Front Wheel Drive Shaft Outer Joint and Boot Replacement

Special Tools

    • GE-396 Snap Ring Pliers
    • CH-804 Tensioner

For equivalent regional tools, refer to Special Tools .

Removal Procedure

  1. Remove the left or right wheel drive shaft. Refer to Front Wheel Drive Shaft Replacement - Left Side or Front Wheel Drive Shaft Replacement - Right Side .

  2. 2027958
  3. Remove the large seal retaining clamp from the CV joint with a side cutter. Discard the seal retaining clamp.
  4. Warning: Use of eye goggles is necessary to prevent personal injury.

  5. If equipped with a small swage ring, use a hand grinder to cut through the swage ring, taking care not to damage the halfshaft bar, in order to remove the swage ring. Otherwise, remove the small seal retaining clamp with a side cutter. DISCARD the retaining clamp.
  6. Separate the halfshaft outboard seal from CV joint outer race (1) at large diameter.
  7. Slide the seal (4) away from joint along halfshaft bar (5).
  8. Wipe the grease from the face of the CV joint inner race (2).
  9. Spread the ears on the race retaining ring (3) with GE-396 pliers (6).
  10. Remove the CV joint assembly (1) from the halfshaft bar (5).
  11. Remove the halfshaft outboard seal (4) from the halfshaft bar (5).
  12. DISCARD the old outboard seal.
  13. Clean the following items thoroughly with cleaning solvent. Remove all traces of old grease and any contaminates.
  14. • The inner and outer race assemblies
    • The CV joint cage
    • The chrome alloy balls
  15. Dry all the parts.
  16. Check the CV joint assembly for the following items:
  17. • Unusual wear
    • Cracks
    • Damage
  18. Clean the halfshaft bar. Use a wire brush to remove any rust in the seal mounting area (grooves).

Installation Procedure


    2027976

    Note: Place a towel in the vise before inserting the halfshaft.

  1. Mount the halfshaft into a vise.
  2. Install the NEW small eared clamp (2) on the neck of the outboard seal (1). Do not crimp.
  3. Slide the outboard seal (1) onto the halfshaft bar and position the neck of the outboard seal (1) in the seal groove on the halfshaft bar. The largest groove below the sight groove on the halfshaft bar is the seal groove (3).
  4. Caution: Refer to Fastener Caution in the Preface section.


    2027983
  5. Crimp the eared clamp, using the CH-804 tensioner (1), and a torque wrench. Tighten the eared clamp to  25 N·m 19 (lb ft).
  6. Place approximately half the grease from the service kit inside the outboard seal and pack the CV joint with the remaining grease.

  7. 2027984
  8. Push the CV joint (2) onto the halfshaft bar (1) until the retaining ring is seated in the groove on the halfshaft bar.

  9. 2027985

    Note: The outboard seal (1) must not be dimpled, stretched or out of shape in any way. If the outboard seal (1) is not shaped correctly, equalize the pressure in the outboard seal (1) and shape the seal properly by hand.

  10. Slide large diameter of the outboard seal (1) with the large seal retaining clamp (2) in place over the outside of the CV joint outer race (3) and locate the seal lip in the groove on the CV joint outer race.

  11. 2027983
  12. Crimp the seal retaining clamp (1) using CH-804 tensioner to  25 N·m 19 (lb ft).
  13. Install the left or right wheel drive shaft. Refer to Front Wheel Drive Shaft Replacement - Left Side or Front Wheel Drive Shaft Replacement - Right Side .
   


© Copyright Chevrolet. All rights reserved
   


© Copyright Chevrolet. All rights reserved