Service Information

Orlando

DTC B1325, B1330, B1517, C0800, P0560, P0562, or P0563

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC B1325 03: Control Module Power Circuit Low Voltage

DTC B1325 07: Control Module Power Circuit High Voltage

DTC B1330 03: Control Module Power 2 Circuit Low Voltage

DTC B1517 03: Battery Voltage Low Voltage

DTC B1517 07: Battery Voltage High Voltage

DTC B1517 5A : Battery Voltage Not Plausible

DTC C0800 03: Control Module Power Circuit Low Voltage

DTC C0800 07: Control Module Power Circuit High Voltage

DTC C0800 0D: Control Module Power Circuit High Resistance

DTC C0800 11: Control Module Power Circuit High Input

DTC P0560 00: System Voltage Malfunction

DTC P0562 00: System Voltage Low Voltage

DTC P0563 00: System Voltage High Voltage

Circuit/System Description

The vehicle control modules or sensors monitor the system voltage to verify the system voltage is within the normal operating range.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The control module or sensor detects a system voltage of less than approximately 9 V for approximately 5 s.

Action Taken When the DTC Sets

•	A driver information centre message and/or warning indicator may be displayed.

•	The control module may be temporarily disabled.

Conditions for Clearing the DTC

The system voltage returns to normal operating range.

Diagnostic Aids

•	A high or low voltage DTC set or voltage value in multiple modules/sensors indicates a concern in the charging system.

•	A possible cause of this DTC may be overcharging with a battery charger or jump starting.

Reference Information

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition OFF, measure and record the battery voltage at the battery terminals. The battery voltage should stabilise between 12.4-12.8 V within a few minutes of turning the ignition OFF.

⇒	If not within the specified range, refer to Battery Inspection/Test .

Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be at least 1 V greater than the voltage measured in step 1 but less than 15 V.

⇒	If not within the specified range, refer to Charging System Test .

Observe the appropriate module scan tool B+ and ignition voltage parameters. The voltage readings should be within 1 V of the battery voltage.

Circuit/System Testing

Note: Use the schematic to identify the following:

•	Control modules the vehicle is equipped with

•	The control modules ground, B+, and ignition circuit terminal IDs and connectors

Ignition OFF, disconnect the harness connectors at the appropriate control module.

Note: Some control module ground circuits may require up to 20 minutes to achieve a resistance reading of less than 10 Ω. In most cases the readings will drop below 20 Ω within 1 min indicating the control modules are going to sleep.

Ignition OFF, scan tool disconnected, open and close the driver door and wait 1 minute. Test for less than 10 Ω between each ground circuit terminal and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.

⇒	If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

Note: If the ignition circuit in Step 4 is providing voltage from a relay that has its coil grounded through the control module connector, you will have to connect a fused bridging wire from the relay ground to a good ground to verify the ignition circuit works correctly.

If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.

⇒	If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

If all circuits test normal, replace the control module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for control module replacement, setup, and programming