To the top of the document
Spark
To Previous Page To Next Page
GMDE Start Page Load static TOC Load dynamic TOC Help?

SECTION 2

ENGINE COMPARTMENT

1. COMPONENTS CONNECTION LOOSE

Check engine compartment for components which may be loose; kinked or pinched vacuum hoses or electrical connections, and for any other missing or disconnected components as below.

uzw6171a
Display graphic Translations of text in graphics


  1. Air Cleaner
  2. Engine oil filter cap
  3. Brake fluid reservoir*
  4. Clutch fluid reservoir*
  5. Coolant reservoir
  6. fuse and relay box
  7. battery
  8. Washer fluid reservoir
  9. Power steering fluid reservoir
  10. Engine oil level dipstick
If remedy is required, tighten clamps, connections, bolts and nuts, and replace or repair defective hose and its connections.

2. HOSE AND ELECT. WIRES ROUTING

Check to assure that following hoses and electrical wires are properly routed to provide sufficient clearance with adjacent moving or hot parts.

3. FREENESS OF MOVEMENT OF LINKAGE, VALVES AND OTHER COMPONENTS

Observe the movement or freeness of movement of valves and other components.

Note : Do not run the starter motor too long as this puts a severe strain on the battery.

4. UNUSUAL NOISES

Check for unusual noises within engine compartment.
Run the engine and check if there are some unusual noises. If unusual noises are heard, fasten or fix the loosen parts and adjust the clearance between components.

5. SEEPAGE AND LEAKS AT HOSES AND PIPE CONNECTIONS, ETC.

Visually inspect for seepage and leaks at hoses and pipe connection, seals, gaskets and plugs. Tighten clamps and connection as necessary.

6. POWER STEERING SYSTEM

Check power steering gear, lines and hoses for leaks and clearance with adjacent panels, moving or hot parts.
Tighten clamps and connectors as necessary.

4950wr
Display graphic Translations of text in graphics


7. ENGINE COOLANT PROTECTION

Test engine coolant protection
<Example: TACUMA(REZZO)>
Description
Cooling fan Operating Mode
Fan operating Temp.(°C)
ON
OFF
A/C OFF or Non-A/C model
Low speed
96
93
High speed
100
97
A/C ON
Low speed
when the A/C system id ON
High speed
100
97

1650e
Display graphic Translations of text in graphics


8. ALL FLUID LEVELS CHECK

Check all fluid levels; engine oil, transmission oil, power steering oil, brake and cooling system.

uzw6061a
Display graphic Translations of text in graphics


Note : Removal of the fluid level plug when the transaxle fluid is hot may cause injury if fluid drains from the fluid level plug.

uzw6171a
Display graphic Translations of text in graphics


Note : Use only special fluids as specified in the Owner's Manual.

uzw6141a
Display graphic Translations of text in graphics


Note : Fluid specification DOT 4 or DOT 4Plus

uzw6121a
Display graphic Translations of text in graphics


Note : Do not overfill and remove the coolant surge tank cap when the engine and radiator are hot.

Note : The anti-freeze content of the coolant should be maintained at a minimum of 50% and maximum of 60%.

Note : Only use coolant that is specified in the Owner's Manual.

uzw6091a
Display graphic Translations of text in graphics


Note : Do not use radiator anti-freeze for windscreen washer solution. Because this may result in damage to the paint work.

uzw6221a
Display graphic Translations of text in graphics


Note : Fluid specification DEXRON® VI

uzw6191a
Display graphic Translations of text in graphics


9. BELTS TENSION

Note : to check belt tension easily, apply moderate thumb pressure (Approx. 10 Kg) midway between pulleys, and check the deflection. If the belt goes down by 10 mm, it is normal.

uzw6311a
Display graphic Translations of text in graphics


To Previous Page To Next Page


© Copyright Chevrolet Europe. All rights reserved
=