Service Manual2007 Captiva DIAGNOSTIC TROUBLE CODE DIAGNOSIS

Captiva

DIAGNOSTIC TROUBLE CODE DIAGNOSIS

Diagnostic Trouble Code Chart

DTC	DESCRIPTION	TYPE	Illuminate MIL	Illuminate SVS
P0562	System Voltage Low	A	Yes	No
P0563	System Voltage High	A	Yes	No
P0601	Transmission Control Module (TCM) Read Only Memory (ROM)	A	Yes	No
P0602	Transmission Control Module (TCM) Not Programmed	C1	No	Yes
P0603	Transmission Control Module (TCM) Long Term Memory Reset	A	Yes	No
P0604	Transmission Control Module (TCM) Random Access Memory	A	Yes	No
P0705	Transmission Range (TR) Switch Circuit	A	Yes	No
P0711	Transmission Fluid Temperature (TFT) Sensor Performance	A	Yes	No
P0712	Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage	A	Yes	No
P0713	Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage	A	Yes	No
P0717	Input Speed Sensor Circuit Low Voltage	A	Yes	No
P0722	Output Speed Sensor Circuit Low Voltage	A	Yes	No
P0731	Incorrect 1st Gear Ratio	A	Yes	No
P0732	Incorrect 2nd Gear Ratio	A	Yes	No
P0733	Incorrect 3rd Gear Ratio	A	Yes	No
P0734	Incorrect 4th Gear Ratio	A	Yes	No
P0735	Incorrect 5th Gear Ratio	A	Yes	No
P0736	Incorrect Reverse Ratio	A	Yes	No
P0762	Shift Solenoid (SS) 3 Valve Performance – Stuck ON	A	Yes	No
P0962	Line Pressure Control (PC) Solenoid Control Circuit Low Voltage	A	Yes	No
P0963	Line Pressure Control (PC) Solenoid Control Circuit High Voltage	A	Yes	No
P0970	Shift Pressure Control (PC) Solenoid Control Circuit Low Voltage	A	Yes	No
P0971	Shift Pressure Control (PC) Solenoid Control Circuit High Voltage	A	Yes	No
P0973	Shift Solenoid (SS) 1 Control Circuit Low Voltage	A	Yes	No
P0974	Shift Solenoid (SS) 1 Control Circuit High Voltage	A	Yes	No
P0976	Shift Solenoid (SS) 2 Control Circuit Low Voltage	A	Yes	No
P0977	Shift Solenoid (SS) 2 Control Circuit High Voltage	A	Yes	No
P0979	Shift Solenoid (SS) 3 Control Circuit Low Voltage	A	Yes	No
P0980	Shift Solenoid (SS) 3 Control Circuit High Voltage	A	Yes	No
P0982	Shift Solenoid (SS) 4 Control Circuit Low Voltage	A	Yes	No
P0983	Shift Solenoid (SS) 4 Control Circuit High Voltage	A	Yes	No
P0985	Shift Solenoid (SS) 5 Control Circuit Low Voltage	A	Yes	No
P0986	Shift Solenoid (SS) 5 Control Circuit High Voltage	A	Yes	No
P1715	Incorrect 1st Gear Ratio (SS5: OFF, TCC lock up PC Solenoid (SLU) :OFF)	A	Yes	No
P1719	Incorrect Shifting Detected	A	Yes	No
P2533	Ignition Line Ground or Open	A	Yes	No
P2757	Torque Converter Clutch (TCC) Lock Up Pressure Control (PC) Solenoid – Stuck OFF	A	Yes	No
P2758	Torque Converter Clutch (TCC) Lock Up Pressure Control (PC) Solenoid – Stuck ON	A	Yes	No
P2763	Torque Converter Clutch (TCC) Lock Up Pressure Control (PC) Solenoid Control Circuit High Voltage	A	Yes	No
P2764	Torque Converter Clutch (TCC) Lock Up Pressure Control (PC) Solenoid Control Circuit Low Voltage	A	Yes	No
U0001	CAN BUS OFF Counter Overrun	A	Yes	No
U0100	Lost Communication With ECM	A	Yes	No
U0121	Lost Communication With ABS	C1	No	Yes
U0140	Lost Communication With BCM	C1	No	Yes
U0401	Invalid data Received From ECM	C1	No	Yes
U0422	Tiptronic Signal Failure (Invalid Data Received From BCM)	C1	No	Yes

* Description of Type

Type A : TCM will request the illumination of MIL and store DTC when TCM detects a failure on the first ignition cycle.
Type C1 : TCM will request the illumination of SVS and store DTC when TCM detects failures on the first ignition cycle.

Diagnostic Trouble Code (DTC) P0562

System Voltage Low

Conditions for Running the DTC

Emergency mode is OFF.
No failure condition of BUS OFF/ECM No ID.
No failure of engine speed.
Engine speed is more than 400 RPM.

Conditions for Setting the DTC

The system voltage is less than 9 volts for 20 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur:

The transmission will operate in 4th gear when the transmission is shifted into D ,M+ or 4 th range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

TCM wiring harness and connectors
Battery
TCM

DTC P0562 - System Voltage Low

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. Turn the ignition ON, with the engine OFF. Run the engine to 400 rpm or greater. Record then clear DTC(s). Select system voltage on the scan tool. Drive the vehicle and observe the scan tool for either of the flowing conditions: Is the voltage within the values shown?	9-16v	Go to Step 4	Go to Step 2
2	Disconnect the battery cable. Measure the battery voltage. Is the voltage within the values shown?	9-16v	Go to Step 4	Go to Step 3
3	Replace the battery. Is the replacement completed?	-	System OK	-
4	Turn the headlamp ON. Turn the air conditioner ON. Run the engine to 400 rpm or greater. Observe the scan tool for system voltage. Is the voltage within the values shown?	9-16v	Go to Step 6	Go to Step 5
5	Turn the ignition LOCK. Repair the alternator circuit if necessary. Is the action completed?	-	System OK	-
6	Inspect the Ef32, Ef30, F29 fuse for an open. Was a problem found?	-	Go to Step 7	Go to Step 8
7	Inspect the Ef32, Ef30, F29 fuse for short. Replace the fuse if necessary. Is the replacement complete?	-	System OK	-
8	Turn the ignition ON. Measure the voltage of Ef32, Ef30, F29. Is the voltage within the values shown?	9-16v	Go to Step 10	Go to Step 9
9	Repair the fuse voltage supply lines for open. Is the action completed?	-	System OK	-
10	Turn the ignition LOCK. Disconnect the TCM wiring connector. Measure the resistance between Ef32 fuse and terminal 6 of the TCM wiring connector J1. Measure the resistance between Ef20 fuse and terminal 22 of the TCM wiring connector J2. Is the resistance within the values shown?	0Ω	Go to Step 12	Go to Step 11
11	Repair the circuit (between Ef32 and terminal 6 of connector J1 for short to ground and open.) Repair the circuit (between Ef20 and terminal 22 of connector J2) for short to ground and open. Is the repair completed?	-	System OK	-
12	Disconnect the X201 connector and TCM connector. Turn the ignition ON. Measure the voltage of the terminal 22 of connector J2. Is the voltage within the values shown?	9-16v	Go to Step 13	Go to Step 14
13	Repair the circuit from Ef20 to terminal 22 of the TCM connector J2 for short to battery. Is the repair complete?	-	System OK	-
14	Turn the ignition LOCK. Measure the resistance between F29 fuse and terminal 21 of the TCM wiring connector J2. Is the resistance within the values shown?	0Ω	Go to Step 17	Go to Step 15
15	Repair the circuit (between F29 and terminal 21 of connector J2) for short to ground and open. Is the repair complete?	-	System OK	-
16	Turn the ignition ON. Measure the voltage of the terminal 21 of connector J2. Is the voltage within the values shown?	9-16v	Go to Step 17	Go to Step 18
17	Repair the circuit (between F29 and terminal 21 of connector J2) for short to battery. Is the repair complete?	-	System OK	-
18	Inspect the transaxle wiring for poor electrical connectors at the transaxle connector. Look for possible bent, backed out, deformed, or damaged terminals. Check for week terminal tension. Was a condition found?	-	Verify repair and Go to Step 20	-
19	Replace the TCM. Is the replacement complete?	-	Go to Step 20	-
20	After the repair, use a scan tool "clear info" function and road test the vehicle. Review the "DTC info". Has the last test failed or is the current DTC displayed?	-	Begin diagnosis again	Repair verified Exit DTC chart

Diagnostic Trouble Code (DTC) P0563

System Voltage High

Conditions for Running the DTC

Emergency mode is OFF.
No failure condition of BUS OFF/ECM No ID.
No failure of engine speed.
Engine speed is more than 400 RPM.

Conditions for Setting the DTC

The system voltage is more than 18 volts for 20 seconds

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur:

The transmission will operate in 4th gear when the transmission is shifted into D , M+, or 4th gear range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

TCM wiring harness and connectors
Battery
TCM

DTC P0563 - System Voltage High

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. Turn the ignition ON, with the engine OFF. Run the engine to 400 rpm or greater. Record then clear DTC(s). Select system voltage on the scan tool. Drive the vehicle and observe the scan tool for either of the flowing conditions: Is the voltage within the values shown?	9-16v	Go to Step 4	Go to Step 2
2	Disconnect the battery cable. Measure the battery voltage. Is the voltage within the values shown?	9-16v	Go to Step 4	Go to Step 3
3	Replace the battery. Is the replacement completed?	-	System OK	-
4	Turn the headlamp ON. Turn the air conditioner ON. Run the engine to 400 rpm or greater. Observe the scan tool for system voltage. Is the voltage within the values shown?	9-16v	Go to Step 6	Go to Step 5
5	Turn the ignition LOCK. Repair the alternator circuit if necessary. Is the action completed?	-	System OK	-
6	Inspect the Ef32, Ef30, F29 fuse for an open. Was a problem found?	-	Go to Step 7	Go to Step 8
7	Inspect the Ef32, Ef30, F29 fuse for short. Replace the fuse if necessary. Is the replacement complete?	-	System OK	-
8	Turn the ignition ON. Measure the voltage of Ef32, Ef30, F29. Is the voltage within the values shown?	9-16v	Go to Step 10	Go to Step 9
9	Repair the fuse voltage supply lines for open. Is the action completed?	-	System OK	-
10	Turn the ignition LOCK. Disconnect the TCM wiring connector. Measure the resistance between Ef32 fuse and terminal 6 of the TCM wiring connector J1. Measure the resistance between Ef20 fuse and terminal 22 of the TCM wiring connector J2. Is the resistance within the values shown?	0Ω	Go to Step 12	Go to Step 11
11	Repair the circuit (between Ef32 and terminal 6 of connector J1 for short to ground and open.) Repair the circuit (between Ef20 and terminal 22 of connector J2) for short to ground and open. Is the repair completed?	-	System OK	-
12	Disconnect the X201 connector and TCM connector. Turn the ignition ON. Measure the voltage of the terminal 22 of connector J2. Is the voltage within the values shown?	9-16v	Go to Step 13	Go to Step 14
13	Repair the circuit from Ef20 to terminal 22 of the TCM connector J2 for short to battery. Is the repair complete?	-	System OK	-
14	Turn the ignition LOCK. Measure the resistance between F29 fuse and terminal A6 of the TCM wiring connector J2. Is the resistance within the values shown?	0Ω	Go to Step 17	Go to Step 15
15	Repair the circuit (between F29 and terminal 21 of connector J2) for short to ground and open. Is the repair complete?	-	System OK	-
16	Turn the ignition ON. Measure the voltage of the terminal 21 of connector J2. Is the voltage within the values shown?	9-16v	Go to Step 17	Go to Step 18
17	Repair the circuit (between F29 and terminal 21 of connector J2) for short to battery. Is the repair complete?	-	System OK	-
18	Inspect the transaxle wiring for poor electrical connectors at the transaxle connector. Look for possible bent, backed out, deformed, or damaged terminals. Check for week terminal tension. Was a condition found?	-	Verify repair and Go to Step 20	-
19	Replace the TCM. Is the replacement complete?	-	Go to Step 20	-
20	After the repair, use a scan tool "clear info" function and road test the vehicle. Review the "DTC info". Has the last test failed or is the current DTC displayed?	-	Begin diagnosis again	Repair verified Exit DTC chart

Diagnostic Trouble Code (DTC) P0601

Transmission Control Module (TCM) Read Only Memory (ROM)

Conditions for Running the DTC

TCM runs the program to detect internal fault when the engine is running.

Conditions for Setting the DTC

TCM detects the calculated checksum is different from the correct checksum value in ROM.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur:

The transmission will operate in 4 th gear when the transmission is shifted into D , M+, or 4th gear range

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Harness or connector between TCM and ECM
ECM
TCM

DTC P0601 - Transmission Control Module (TCM) Read Only Memory (ROM)

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0601 displayed?	-	Replace the Transmission Control Module (TCM).	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.

Diagnostic Trouble Code (DTC) P0602

Transmission Control Module (TCM) Not Programmed

Conditions for Running the DTC

Emergency mode is OFF.

Conditions for Setting the DTC

Data is not written in the fixed address in the calibration area.

Action Taken When the DTC Sets

TCM will request the BCM to illuminate the service vehicle soon (SVS) lamp.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur:

The transmission will operate in 4 th gear when the transmission is shifted into D , M+, or 4th gear range

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the SVS Lamp/DTC

TCM turns OFF the SVS lamp when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Harness or connector between TCM and ECM
ECM
TCM

DTC P0602 - Transmission Control Module (TCM) Not Programmed

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Does the SVS lamp illuminate?	-	Go to Step 2	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0602 displayed?	-	Replace the Transmission Control Module (TCM).	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.

Diagnostic Trouble Code (DTC) P0603

Transmission Control Module (TCM) Long Term Memory Reset

Conditions for Running the DTC

Emergency mode is OFF.

Conditions for Setting the DTC

TCM detects the calculated checksum in RAM is different from the checksum value in EEPROM.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM uses the default value as the initial value for EEPROM.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Harness or connector between TCM and ECM
ECM
TCM

DTC P0603 - Transmission Control Module (TCM) Long Term Memory Reset

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0603 displayed?	-	Replace the Transmission Control Module (TCM).	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.

Diagnostic Trouble Code (DTC) P0604

Transmission Control Module (TCM) Random Access Memory

Conditions for Running the DTC

Emergency mode is OFF.

Conditions for Setting the DTC

TCM can not carry out the four RAM initialization routines.
TCM detects that the RAM can not be written and read correctly.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Harness or connector between TCM and ECM
ECM
TCM

DTC P0604 - Transmission Control Module (TCM) Random Access Memory

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0604 displayed?	-	Replace the Transmission Control Module (TCM).	Inspect Transmission Control Module (TCM) wiring harness and connector for signs of an intermittent condition. Repair as necessary.

Diagnostic Trouble Code (DTC) P0705

Transmission Range (TR) Switch Circuit

Conditions for Running the DTC

The system voltage is 10.2 - 15.5 volts.
The engine is running.

Conditions for Setting the DTC

The combination of TR switch signals is invalid for 5 seconds.

Transmission Range Switch Logic (Up and Down Mode Type).

Postion	A	B	C	PA
P	HI	LOW	LOW	HI
R	HI	HI	LOW	LOW
N	LOW	HI	LOW	HI
D	LOW	HI	HI	LOW

Transmission Range Switch Logic (Straight Type).

Postion	A	B	C	PA
P	HI	LOW	LOW	HI
R	HI	HI	LOW	LOW
N	LOW	HI	LOW	HI
D	LOW	HI	HI	LOW
4	HI	HI	HI	HI
2	HI	LOW	HI	LOW

* HI : Ignition voltage, LOW : 0 Voltage

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur:

The transmission will operate in 4th gear when the transmission is shifted into D , M+, or 4th gear range.

The transmission will operate in 4th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between TR sensor and TCM
TR switch
TCM

DTC P0705 - Transmission Range (TR) Switch Circuit

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0705 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the continuity between the vehicle harness and the Transmission Range (TR) sensor. Disconnect the TCM connector J2 (X-1) of the vehicle harness and inspect the continuity between the terminals as shown chart. Refer to "Unit Inspection" in this section. Does the inspection OK?	-	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and TR sensor. Disconnect the connector (X-2) of the vehicle harness and inspect the continuity between the terminals. Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition of TR sensor OK?	-	Go to Step 7	Replace the TR sensor.
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle harness. Inspect continuity and short circuit for the vehicle harness and inspect the connection condition between connectors (C-2). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0711

Transmission Fluid Temperature (TFT) Sensor Performance

Conditions for Running the DTC

No failure condition of gear range.
Emergency mode is OFF.
The TFT at startup is less than 20°C (68°F).

Conditions for Setting the DTC

The TFT has not changed by more than 5°C (9°F) since startup for 10 minutes.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM uses 30°C (86°F) as a default transmission oil temperature and will start the self learning control after setting TFT as 111°C (232°F) 15 minutes later.
No unusual shifting detection.
Uphill and downhill control are not activated until the TFT is greater than 40°C (104°F) for 5 seconds.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Transmission Fluid Temperature (TFT) sensor and TCM
TFT sensor
TCM

DTC P0711 - Transmission Fluid Temperature (TFT) Sensor Performance

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0711 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Transmission Fluid Temperature (TFT) sensor. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 11 and 12. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and TFT sensor. Disconnect the connector (X-3) of T/M wire and inspect the resistance between TFT sensor connector terminal 1 and 8. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short or open circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of TFT sensor. Inspect the TFT sensor. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace TFT sensor.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short or open circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0712

Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.

Conditions for Setting the DTC

TCM detects a transmission fluid temperature of 200°C (392°F) or more for 5 minutes.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM uses 30°C (86°F) as a default transmission oil temperature and will start the self learning control after setting TFT as 111°C (232°F) 15 minutes later.
No unusual shifting detection.
Uphill and downhill control are not activated until the TFT is greater than 40°C (104°F) for 5 seconds.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Transmission Fluid Temperature (TFT) sensor and TCM
TFT sensor
TCM

DTC P0712 - Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0712 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Transmission Fluid Temperature (TFT) sensor. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 11 and 12. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and TFT sensor. Disconnect the connector (X-3) of T/M wire and inspect the resistance between TFT sensor connector terminal 1 and 8. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short or open circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of TFT sensor. Inspect the TFT sensor. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace TFT sensor.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short or open circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0713

Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Conditions for Running the DTC

The engine run time is 10 minutes or greater.
Engine coolant temperature(ECT) is greater than 50°C (122°F).
No ECT DTCs.
Emergency mode is OFF.

Conditions for Setting the DTC

TCM detects a transmission fluid temperature of -46°C (-51°F) or less for 12 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM uses 30°C (86°F) as a default transmission oil temperature and will start the self learning control after setting TFT as 111°C (232°F) 15 minutes later.
No unusual shifting detection.
Uphill and downhill control are not activated until the TFT is greater than 40°C (104°F) for 5 seconds.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Transmission Fluid Temperature (TFT) sensor and TCM
TFT sensor
TCM

DTC P0713 - Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0713 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Transmission Fluid Temperature (TFT) sensor. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 11 and 12. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and TFT sensor. Disconnect the connector (X-3) of T/M wire and inspect the resistance between TFT sensor connector terminal 1 and 8. Is the measurement within the specified value?	10°C (50°F) : 5.80-7.09 kΩ 110°C (230°F) : 0.231-0.263 kΩ	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short or open circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of TFT sensor. Inspect the TFT sensor. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace TFT sensor.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short or open circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0717

Input Speed Sensor Circuit Low Voltage

Conditions for Running the DTC

Fail Case 1

If the vehicle speed is 66km/h(41mph) or transmission oil temperature is greater than 20°C (68°F), the gear range is changed from P,R,N range to others for 2.5 seconds or greater.
If the transmission oil temperature is 0-20°C (32-68°F), the gear range is changed from P,R,N range to others for 10 seconds or greater.
If the transmission oil temperature is less than 0°C (32°F), the gear range is changed from P,R,N range to others for 180 seconds or greater.
Output speed is greater than 600 RPM.
No gear selector failure.
The transmission is not shifting.
TCM is not in ND control.
The commanded gear is 2 or greater.
No TFT DTCs.
Emergency mode is OFF.

Fail Case 2

System voltage is 10.2-15.5 volts.
Emergency mode is OFF

Fail Case 3 (For the vehicle equipped with ABS)

If the vehicle speed is 66km/h(41mph) or transmission oil temperature is greater than 20°C (68°F), the gear range is changed from P,R,N range to others for 2.5 seconds or greater.
If the transmission oil temperature is 0-20°C (32-68°F), the gear range is changed from P,R,N range to others for 10 seconds or greater.
If the transmission oil temperature is less than 0°C (32°F), the gear range is changed from P,R,N range to others for 180 seconds or greater.
Output speed is greater than 600 RPM.
No gear selector failure.
The transmission is not shifting.
TCM is not in ND control.
The commanded gear is 2 or greater.
No TFT DTCs.
Emergency mode is OFF.

Conditions for Setting the DTC

Fail Case 1

TCM does not detect any pulses from the input speed sensor while detecting 3,000 pulses of the output speed sensor signal.

Fail Case 2

Input speed sensor signal circuit is open or shorted for 30 seconds or greater.

Fail Case 3 (For the vehicle equipped with ABS)

Input speed RPM is equal to 0 and ABS vehicle speed is greater than 20 km/h (12 mph) for 30 seconds or greater.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4 th gear when the transmission is shifted into D , M+, or 4 th gear range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Input Speed Sensor and TCM
Input Speed Sensor
TCM

DTC P0717 - Input Speed Sensor Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0717 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Inspect the vehicle harness. Disconnect the connector(X-1,C-4) of the vehicle harness and inspect the continuity. Is the inspection OK?	-	Go to Step 4	Go to Step 5
4	Estimate the failure of input speed sensor and TCM. Inspect the input speed sensor. Refer to " Unit Inspection" in this section. Is the measurement within the specified value?	At high signal :12.0-16.0 mA At low signal : 4.0-8.0 mA	Go to Step 6	Replace the input speed sensor.
5	Estimate the failure of the vehicle harness. Inspect the vehicle harness and connector. Inspect the connection condition for the connector (C-1,C-4). Inspect the broken harness. Is the inspection OK?	-	Inspect the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the harness or adjustment between connectors.
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.

Diagnostic Trouble Code (DTC) P0722

Output Speed Sensor Circuit Low Voltage

Conditions for Running the DTC

Fail Case 1

If the vehicle speed is 66km/h(41mph) or transmission oil temperature is greater than 20°C (68°F), the gear range is changed from P,R,N range to others for 2.5 seconds or greater.
If the transmission oil temperature is 0-20°C (32-68°F), the gear range is changed from P,R,N range to others for 10 seconds or greater.
If the transmission oil temperature is less than 0°C (32°F), the gear range is changed from P,R,N range to others for 180 seconds or greater.
No gear selector failure.
No TFT DTCs.
The transmission is not shifting.
TCM is not in ND control.
Emergency mode is OFF.

Fail Case 2

System voltage is 10.2-15.5volts.
Emergency mode is OFF.

Fail Case 3 (For the vehicle equipped with ABS)

If the vehicle speed is 66km/h(41mph) or transmission oil temperature is greater than 20°C (68°F), the gear range is changed from P,R,N range to others for 2.5 seconds or greater.
If the transmission oil temperature is 0-20°C (32-68°F), the gear range is changed from P,R,N range to others for 10 seconds or greater.
If the transmission oil temperature is less than 0°C (32°F), the gear range is changed from P,R,N range to others for 180 seconds or greater.
No gear selector failure.
No TFT DTCs.
The transmission is not shifting.
TCM is not in ND control.
Emergency mode is OFF.

Conditions for Setting the DTC

Fail Case 1

TCM does not detect any pulses from the output speed sensor while detecting 6,000 pulses of the input speed sensor signal.

Fail Case 2

Output speed sensor signal circuit is open or shorted for 30 seconds or greater.

Fail Case 3 (For the vehicle equipped with ABS)

Output speed RPM is equal to 0 and ABS vehicle speed is greater than 20 km/h (12 mph) for 30 seconds or greater.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met.TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D , M+, or 4th gear range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Output Speed Sensor and TCM
Output Speed Sensor
TCM

DTC P0722 - Output Speed Sensor Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0722 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Inspect the vehicle harness. Disconnect the connector (X-1,C-4) of the vehicle harness and inspect the continuity. Is the inspection OK?	-	Go to Step 4	Go to Step 5
4	Estimate the failure of output speed sensor and TCM. Inspect the output speed sensor. Refer to " Unit Inspection" in this section. Is the measurement within the specified value?	At high signal :12.0-16.0 mA At low signal : 4.0-8.0 mA	Go to Step 6	Replace the output speed sensor.
5	Estimate the failure of the vehicle harness. Inspect the vehicle harness and connector. Inspect the connection condition for the connector (C-1,C-4). Inspect the broken harness. Is the inspection OK?	-	Inspect the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the harness or adjustment between connectors.
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.