To the top of the document
Cruze
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC P0622

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0622 00: Generator F-Terminal Circuit

DTC P0622 11: Generator F-Terminal Circuit High Input

DTC P0622 12: Generator F-Terminal Circuit Low Input

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+

-

P0622 00, P0622 12

-

-

Control

P0621 00, P0621 58

P0621 00, P0621 58

P0621 00, P0621 58

-

Signal

P0622 00, P0622 12

P0622 00, P0622 12

P0622 00, P0622 12

P0622 00, P0622 12

Circuit/System Description

The engine control module (ECM) uses the generator field duty cycle control circuit, or F-terminal circuit, to monitor the duty cycle of the generator. The generator field duty cycle signal circuit connects to high side of the field windings in the generator. A pulse width modulated (PWM) high side driver in the voltage regulator turns the field windings ON and OFF. The ECM uses the PWM control input to determine the generator load on the engine. This allows the ECM to adjust the idle speed to compensate for high electrical loads. The ECM monitors the status of the generator field duty cycle control circuit. When the ignition is ON and the engine is OFF, the ECM should detect a duty cycle near 0 percent. When the engine is running, the duty cycle should be between 5–99 percent.

Conditions for Running the DTC
    • Ignition ON engine OFF, for the Ignition ON test.
    • Engine running, engine speed less than 3,000 RPM for the RUN test.

Conditions for Setting the DTC
    •  DTC P0621 is not set.
    • Ignition ON engine OFF, the ECM detects a PWM signal that is greater than 65 percent for 5 seconds.
    • Engine running, the ECM detects a PWM signal that is less than 5 percent for 15 seconds.

Action Taken When the DTC Sets

DTC P0622 is a C type DTC.

Conditions for Clearing the DTC

DTC P0622 is a C type DTC.

Reference Information

Schematic Reference

Starting and Charging Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Charging System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Engine running, observe the scan tool GEN-F Terminal Control Circuit parameter. The GEN-F Terminal Control Circuit parameter should display between 5-95 percent.

Circuit/System Testing
  1. Verify that a test lamp illuminates between the G13 alternator B+ output circuit X1 terminal 1 and ground.
    2. ⇒If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  2. Ignition OFF, disconnect the X2 harness connector at the G13 generator.
  3. Ignition ON, verify the scan tool ECM GEN-F Terminal Signal parameter displays less than 5 percent.
    4. ⇒If greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the K20 ECM.
  4. Install a 3 A fused jumper wire between B+ and the signal circuit terminal 2.
  5. Verify the scan tool ECM GEN-F Terminal Signal parameter displays greater than 95 percent.
    6. ⇒ If less than the specified range, test the signal circuit terminal 2 for a short to ground or an open/high resistance. If the circuit tests normal, replace the K20 ECM.
  6. If the circuit tests normal replace the G13 generator.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Generator Replacement : 2.0L Diesel LNP → 2.0L Diesel LLW → 1.4L LDD, LUH, and LUJ → 1.6L LXT,L2W → 1.6L LDE, LXV, LLU, 1.8L 2H0, and LUW
    • Control Module References for ECM replacement, setup, and programming
   


© Copyright Chevrolet. All rights reserved