Service Information

Cruze

DTC B1405

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC B1405 02: Control Module Voltage Reference Output 2 Circuit Short to Ground

DTC B1405 03: Control Module Voltage Reference Output 2 Circuit Low Voltage

DTC B1405 07: Control Module Voltage Reference Output 2 Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
8V Reference	B1405 02	B0958 06, B0959 06, B0960 06, B0961 06, B1405 03	B0958 06, B0959 06, B0960 06, B0961 06, B1405 07	--
Left Rear Object Sensor Signal	B0958 06	B0958 06	B0958 01	B0958 08, B0958 21
Left Middle Rear Object Sensor Signal	B0959 06	B0959 06	B0959 01	B0959 08, B0959 21
Right Middle Rear Object Sensor Signal	B0960 06	B0960 06	B0960 01	B0960 08, B0960 21
Right Rear Object Sensor Signal	B0961 06	B0961 06	B0961 01	B0961 08, B0961 21
Low Reference	--	B0958 06, B0959 06, B0960 06, B0961 06	--	--

Circuit/System Description

The object sensors are 3-wire sensors that are used to determine the distance between the vehicle and an object of interest. The parking assist control module supplies 8 V to the object sensors via the 8 V reference circuit and provides ground via the low reference circuit. The parking assist control module triggers the sensors in a sequential loop. After each sensor transmits, the parking assist control module uses the sensor echo received through the signal circuit to calculate the distance and position of an object.

Conditions for Running the DTC

•	Ignition ON

•	Transmission in REVERSE

Conditions for Setting the DTC

B1405 02

The parking assist control module has detected the 8 V reference circuit is shorted to ground.

B1405 03

The parking assist control module has detected the 8 V reference circuit is less than 6.3 V.

B1405 07

The parking assist control module has detected the 8 V reference circuit is greater than 10.4 V.

Action Taken When the DTC Sets

•	The parking assist is disabled.

•	The driver information centre displays SERVICE PARK ASSIST.

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Reference Information

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, transmission in REVERSE, observe the scan tool Park Assist Sensors Reference Voltage parameter. The reading should be between 6.3-10.4 V.

Circuit/System Testing

Ignition OFF, disconnect the harness connector at each of the object sensors.
Ignition ON, transmission in REVERSE, test for 6.3-10.4 V between the 8 V reference circuit terminal 1 at the B78G Rear Object Sensor - Left Outer harness connector and ground.

⇒	If less than the specified range, test the 8 V reference circuit for a short to ground. If the circuit tests normal, replace the K41 Parking Assist Control Module.

⇒	If greater than the specified range, test the 8 V reference circuit for a short to voltage. If the circuit tests normal, replace the K41 Parking Assist Control Module.

Install each object alarm sensor harness connector one at a time, checking DTCs after each sensor is connected. Verify DTC B1405 is not set as current.

⇒	If the DTC is set, replace the object alarm sensor that was connected immediately before the DTC set.

If all circuits test normal, replace the K41 Parking Assist Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

•	Rear Parking Assist Alarm Sensor Replacement

•	Control Module References for parking assist control module replacement, setup and programming.