Cruze

DTC P0069

The turbocharger pressure sensor responds to pressure changes in the inlet manifold. The pressure changes occur based on the engine load, and turbocharger boost. The engine control module (ECM) supplies 5 V to the turbocharger pressure sensor on the 5 V reference circuit. The ECM provides an ground on the low reference circuit. The turbocharger pressure sensor provides a signal to the ECM on the sensor signal circuit which is relative to the pressure changes in the manifold. The ECM detects a low signal voltage at a low manifold absolute pressure, such as during deceleration. The ECM detects a high signal voltage at a high manifold absolute pressure, such as the ignition is ON, with the engine OFF, or at idle. The barometric pressure (BARO) sensor is internal to the ECM. This location allows for constant monitoring of the barometric pressure. The ECM compares the turbocharger pressure sensor signal to the internal BARO sensor signal when the ignition switch is turned ON, with the engine OFF.

The ECM detects that the difference between the manifold absolute pressure signal and the BARO signal is greater than 20 kPa (2.90 PSI) for 1 s.

DTC P0069 00 is a Type B DTC.

DTC P0069 00 is a Type B DTC.

If a shared 5 V reference circuit is shorted to ground or shorted to a voltage, other 5 V reference circuits may be affected.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, observe the DTC information with a scan tool. DTC P0069 00 should not set.

Note: The vehicle used for the comparison is not limited to the same type of vehicle being serviced. A vehicle known to provide an accurate reading is acceptable.

2. Compare the scan tool Boost Pressure Sensor parameter and the scan tool BARO pressure parameter to the pressure parameter of a known good vehicle. Both readings should be within 3 kPa (0.44 PSI) of the known good vehicle.

Note: The Altitude versus Barometric Pressure table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or very low or very high temperature may cause a reading to be slightly out of range.

3. Compare the scan tool Boost Pressure Sensor pressure parameter, and the scan tool BARO pressure parameter, to the reading in the Altitude Versus Barometric Pressure table.
4. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure records data.

1. Ignition ON, compare the scan tool BARO parameter to the reading in the Altitude Versus Barometric Pressure table.

⇒	If not within the specified range, refer to DTC P2122, P2123, P2127, P2128, or P2138 for further diagnosis.

2. Ignition OFF, disconnect the harness connector at the B65 Intake Manifold Pressure and Air Temperature Sensor.
3. Test for less than 5 Ω between the low reference circuit terminal 1 and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module.

4. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground.

⇒	If less than the specified range, test the 5 V reference circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module.

⇒	If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.

5. Verify the scan tool Boost Pressure Sensor parameter is less than 0.3 V.

⇒	If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.

6. Install a 3 A fused jumper wire between the signal circuit terminal 4 and the low reference circuit terminal 3. Verify the Boost Pressure Sensor sensor parameter is at 4.8-5.2 V.

⇒	If less than the specified range, test the signal circuit for an open/high resistance or a short to ground. If the circuit tests normal, replace the K20 Engine Control Module.

7. If all circuits test normal, replace the B65 Inlet manifold Pressure and Air Temperature Sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for ECM replacement, setup, and programming