To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC U0100-U02FF

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC U0100 00: Lost Communication With Engine/Powertrain Control Module (ECM/PCM)

DTC U0101 00: Lost Communication With Transmission Control Module (TCM)

DTC U0102 00: Lost Communication With Transfer Case Control Module (TCCM)

DTC U0104 00: Lost Communication With Cruise Control Module

DTC U0121 00: Lost Communication With Electronic Brake Control Module (EBCM)

DTC U0122 00: Lost Communication With Vehicle Dynamics Control Module

DTC U0131 00: Lost Communication With Power Steering Control Module

DTC U0132 00: Lost Communication With Ride Level Control Module

DTC U0134 00: Lost Communication With Power Steering Control Module-Rear

DTC U0140 00: Lost Communication With Body Control Module (BCM)

DTC U0151 00: Lost Communication With Restraints Control Module

DTC U0155 00: Lost Communication With Instrument Panel Cluster (IPC) Control Module

DTC U0158 00: Lost Communication With Head Up Display

DTC U0160 00: Lost Communication With Audible Alert Control

DTC U0164 00: Lost Communication With HVAC Control Module

DTC U0168 00: Lost Communication With Vehicle Theft Deterrent (VTD) Control Module

DTC U0170 00: Lost Communication With Restraints System Sensor A

DTC U0184 00: Lost Communication With Radio

DTC U0186 00: Lost Communication With Audio Amplifier

DTC U0194 00: Lost Communication With Digital Radio Receiver (DRR)

DTC U0198 00: Lost Communication With Communication Interface Module (OnStar®)

DTC U0199 00: Lost Communication With Door Control Module A

DTC U0200 00: Lost Communication With Door Control Module B

DTC U0201 00: Lost Communication With Door Control Module C

DTC U0202 00: Lost Communication With Door Control Module D

DTC U0209 00: Lost Communication With Heated Seat Module (HSM)

DTC U0214 00: Lost Communication With Remote Function Actuator (RFA)

DTC U0230 00: Lost Communication With Rear Gate Module

DTC U0240 00: Lost Communication With Headlight Control Module A

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Low Speed GMLAN Serial Data

1

U0100-U02FF

1

--

Battery Positive Voltage Circuits

U0100-U02FF

U0100-U02FF

--

--

Ignition Voltage Circuits

U0100-U02FF

U0100-U02FF

--

--

Module Ground Circuits

-

U0100-U02FF

--

--

Serial Data Communication Enable

U2099

U0100-U02FF

--

--

1. Scan Tool Does Not Communicate with Low Speed GMLAN Device

Circuit/System Description

Modules connected to the high and low speed GMLAN serial data circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be exchanged on the serial data circuits, for each virtual network. The messages are supervised and also, some periodic messages are used by the receiver module as an availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The body control module (BCM) activates the serial data communication enable circuit by applying voltage when the ignition key is in ACC, ON or START. The serial data communication enable circuit wakes up the electronic brake control module (EBCM), all wheel drive module, and the electronic power steering control module if equipped for buss communication.

Conditions for Running the DTC
    • The system voltage is between 9–16 V.
    • The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Conditions for Clearing the DTC
    • A current DTC clears when the malfunction is no longer present.
    • A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Reference Information

Schematic Reference

    •  Data Communication Schematics
    •  Control Module References

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Testing
  1. Using the DTC Descriptor and Diagnostic Aids above, determine the module that is not communicating that should be tested.
  2. Ignition OFF, disconnect the harness connector of the module that is not communicating.

    3. Note: Only the high speed GMLAN modules have a serial data communication enable circuit. Refer to the module schematics to identify which modules have these circuits. If the module that is not communicating does not have one of these circuits, proceed to step 4.

  3. Ignition ON, verify that a test lamp illuminates between the serial data communication enable circuit and ground.
    4. ⇒If the test lamp does not illuminate, repair the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
  4. Ignition ON, verify that a test lamp illuminates between all battery positive voltage circuits and ground.
    5. ⇒If the test lamp does not illuminate, repair the circuit for a short to ground or an open/high resistance. If the circuit fuse is open, also test the positive voltage outputs of the module for a short to ground. If the circuits test normal, replace the faulty module.
  5. Verify that a test lamp illuminates between all ignition voltage circuits and ground.
    6. ⇒If the test lamp does not illuminate, repair the circuit for a short to ground or an open/high resistance. If the circuit fuse is open, also test the positive voltage outputs of the module for a short to ground. If the circuits test normal, replace the faulty module.
  6. Test for less than 1 Ω between the module ground circuits and ground.
    7. ⇒If greater than 1 Ω, repair the ground circuit for an open.
  7. Use Data Link References to determine if the non-communicating module should use low speed GMLAN serial data.
    8. ⇒If the module is GMLAN high speed only, replace the module.
  8. Test for less than 1 Ω in the low speed GMLAN serial data circuit between the non-communicating module and the module that displays the DTC.
    9. ⇒If greater than 1 Ω, test the low speed GMLAN serial data circuit for open/high resistance.
  9. If all circuits test normal, replace the module that is not communicating.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  GMLAN Wiring Repairs
    • Control Module References for replacement, setup, and programming
   


© Copyright Chevrolet. All rights reserved