Service Information

Captiva

Remote Control Door Lock Receiver Scan Tool Information

Table 1:	Remote Control Door Lock Receiver Scan Tool Data Parameters
Table 2:	Remote Control Door Lock Receiver Scan Tool Output Controls

Remote Control Door Lock Receiver Scan Tool Data Parameters

Parameter	Expected Value	Definition
*Operating Conditions:* Ignition ON
Key Fob 1 Battery Status	OK	The scan tool displays OK or Low. This is the state of the Fob 1 battery.
Key Fob 1 Function	None	The scan tool displays None, Lock, Driver Door Unlock, All Doors Unlock, Unlock Rear Closure, Actuate Left Sliding Door, Actuate Right Sliding Door, Panic Alarm, Fuel Door Unlatch, Power Window Control, Folding Top Control, Remote Vehicle Start, Stop Engine, Program Key Fobs, Locate Vehicle Alarm, Rear Body Closure Close, Rear Body Closure Open, Rear Body Closure Stop, Dead Lock All Doors, Rear Body Closure Start, or Stop Left Sliding Door Motion. This is the state of the Fob 1 command as monitored by the RCDLR.
Key Fob 1 Status	Learned	The scan tool displays Learned or Not Learned. Learned is displayed if the Fob 1 is programmed into the RCDLR.
Key Fob 2 Battery Status	OK	The scan tool displays OK or Low. This is the state of the Fob 2 battery.
Key Fob 2 Function	None	The scan tool displays None, Lock, Driver Door Unlock, All Doors Unlock, Unlock Rear Closure, Actuate Left Sliding Door, Actuate Right Sliding Door, Panic Alarm, Fuel Door Unlatch, Power Window Control, Folding Top Control, Remote Vehicle Start, Stop Engine, Program Key Fobs, Locate Vehicle Alarm, Rear Body Closure Close, Rear Body Closure Open, Rear Body Closure Stop, Dead Lock All Doors, Rear Body Closure Start, or Stop Left Sliding Door Motion. This is the state of the Fob 2 command as monitored by the RCDLR.
Key Fob 2 Status	Learned	The scan tool displays Learned or Not Learned. Learned is displayed if the Fob 2 is programmed into the RCDLR.
Key Fob 3 Battery Status	OK	The scan tool displays OK or Low. This is the state of the Fob 3 battery.
Key Fob 3 Function	None	The scan tool displays None, Lock, Driver Door Unlock, All Doors Unlock, Unlock Rear Closure, Actuate Left Sliding Door, Actuate Right Sliding Door, Panic Alarm, Fuel Door Unlatch, Power Window Control, Folding Top Control, Remote Vehicle Start, Stop Engine, Program Key Fobs, Locate Vehicle Alarm, Rear Body Closure Close, Rear Body Closure Open, Rear Body Closure Stop, Dead Lock All Doors, Rear Body Closure Start, or Stop Left Sliding Door Motion. This is the state of the Fob 3 command as monitored by the RCDLR.
Key Fob 3 Status	Learned	The scan tool displays Learned or Not Learned. Learned is displayed if the Fob 3 is programmed into the RCDLR.
Key Fob 4 Battery Status	OK	The scan tool displays OK or Low. This is the state of the Fob 4 battery.
Key Fob 4 Function	None	The scan tool displays None, Lock, Driver Door Unlock, All Doors Unlock, Unlock Rear Closure, Actuate Left Sliding Door, Actuate Right Sliding Door, Panic Alarm, Fuel Door Unlatch, Power Window Control, Folding Top Control, Remote Vehicle Start, Stop Engine, Program Key Fobs, Locate Vehicle Alarm, Rear Body Closure Close, Rear Body Closure Open, Rear Body Closure Stop, Dead Lock All Doors, Rear Body Closure Start, or Stop Left Sliding Door Motion. This is the state of the Fob 4 command as monitored by the RCDLR.
Key Fob 4 Status	Learned	The scan tool displays Learned or Not Learned. Learned is displayed if the Fob 4 is programmed into the RCDLR.
Front Tyre Pressure on Placard	Varies	This displays the value in kPA if it is a value from the selectable values in the Tyre Type/Pressure Selection under Configuration/Reset Functions. Otherwise, it displays Standard.
Last Key Fob Detected	Varies	The scan tool displays None, Fob 1, Fob 2, Fob 3, Fob 4 or Fob 5. This was the last Fob used, as monitored by the RCDLR.
Left Front Tyre Pressure Sensor Mode	Varies	The scan tool displays Learn Mode - Remotely Triggered, Re-measure, Drive, Powering Down, Wakeup, or Learn Mode - Pressure Triggered. This is the state of the left front pressure sensor.
Left Front Tyre Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat Tyre, or High. This is the state of the left front tyre pressure.
Left Front Tyre Pressure Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the left front tyre pressure sensor.
Left Front Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left front tyre.
Left Front Tyre Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the left front tyre pressure sensor.
Left Rear Tyre Pressure Sensor Mode	Varies	The scan tool displays Learn Mode - Remotely Triggered, Re-measure, Drive, Powering Down, Wakeup, or Learn Mode - Pressure Triggered. This is the state of the left rear pressure sensor.
Left Rear Tyre Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat Tyre or High. This is the state of the left rear tyre pressure.
Left Rear Tyre Pressure Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the left rear tyre pressure sensor.
Left Rear Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left rear tyre.
Left Rear Tyre Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the left rear tyre pressure sensor.
Rear Tyre Pressure on Placard	Varies	This displays the value in kPA if it is a value from the selectable values in the Tyre Type/Pressure Selection under Configuration/Reset Functions. Otherwise, it displays Standard.
Right Front Tyre Pressure Sensor Mode	Varies	The scan tool displays Learn Mode - Remotely Triggered, Re-measure, Drive, Powering Down, Wakeup, or Learn Mode - Pressure Triggered. This is the state of the right front pressure sensor.
Right Front Tyre Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat Tyre or High. This is the state of the right front tyre pressure.
Right Front Tyre Pressure Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the right front tyre pressure sensor.
Right Front Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right front tyre.
Right Front Tyre Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the right front tyre pressure sensor.
Right Rear Tyre Pressure Sensor Mode	Varies	The scan tool displays Learn Mode - Remotely Triggered, Re-measure, Drive, Powering Down, Wakeup, or Learn Mode - Pressure Triggered. This is the state of the right rear pressure sensor.
Right Rear Tyre Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat Tyre or High. This is the state of the right rear tyre pressure.
Right Rear Tyre Pressure Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the right rear tyre pressure sensor.
Right Rear Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right rear tyre.
Right Rear Tyre Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the right rear tyre pressure sensor.
Selected Front Tyre Type	Varies	The scan tool displays To Tyre Type, Standard Load, Extra Load, Load Range C, Load Range D or Load Range E. This is the type of front tyres used on the vehicle.
Selected Rear Tyre Type	Varies	The scan tool displays To Tyre Type, Standard Load, Extra Load, Load Range C, Load Range D or Load Range E. This is the type of rear tyres used on the vehicle.
Tyre Pressure Monitoring Indicator	Off	The scan tool displays On or Off. This is the state of the TPM indicator.
Tyre Pressure Monitoring System Status	Enabled	The scan tool displays Enabled or Disabled.

Remote Control Door Lock Receiver Scan Tool Output Controls

Scan Tool Output Control	Description
Key Fob Button Test	The RCDLR monitors the incoming RF communications to ensure all keyless entry transmitter functions are operating properly.