Cruze

Engine Support Fixture

Special Tools

For equivalent regional tools refer to, Special Tools

Install EN 47649-100 feet  (4) to EN 47649 bridge  (1).

1. Tighten mounting bolt (2) and nut (6) on both sides.

Put washer (5) under nut on both sides.

2. Tighten adjustment screw (3) when bridge is adjusted vertical on both sides.

1. Install EN 47650-30 extension bars (1, 6) of the frame set to EN 47650 frame .

Note: Outer bars of EN 47650 frame MUST be arranged parallel.

2. Tighten hexagons (2, 6) on both sides.
3. Adjust height of EN 47650 frame .

•	Tighten hexagons (3, 5) on both sides

•	Adjust height with hexagons (4) on both sides

1. Remove the front fender shipping cover. Refer to Front Fender Shipping Cover Replacement .



2. Use short arm (2) of EN 47650-300 adapter for this operation.




Caution: To avoid paint damage, use protective covers on the fenders.

Note: Do NOT tighten fasteners of EN 47650-300 adapter .

3. Install EN 47650-300 adapter  (1) to hole (2) in the front compartment rail.



4. With the aid of an assistant install EN 47650 frame  (1) to the vehicle. If necessary readjust EN 47650 frame  (1) for appropriate fitting.



5. Tighten rear side of EN 47650 frame :

5.1.	Insert safety pins (2) through the EN 47650-300 adapters and the side bar to prevent movement.

5.2.	Tighten EN 47650 frame to EN 47650-300 adapters with mounting bolts (1).

5.3.	Tighten bolts (3, 4)





5.4.	Tighten outer bolts (1) EN 47650-300 adapters .

5.5.	Retighten ALL hexagons of EN 47650 frame .




6. Tighten front side of EN 47650 frame :

6.1.	Align the hook (1) with thumb wheel (2) to upper tie bar.

6.2.	Tighten the hook (1) to upper tie bar, using the thumb wheel (4).

6.3.	Tighten bolts at clamping piece (3).





Note: EN 47650-050 rail is equipment of EN 47650 frame and enclosed in the EN 47650 frame tool kit.

7. Install EN 47650-050 rail  (4) to EN 47650 frame .

Secure EN 47650-050 rail  (4) with safety pins (3).

Note: Secure chain boxes with hook chains on the outside of engine bride.

8. Install EN 47649 bridge  (5) with the aid of an assistant onto EN 47650-050 rail  (4).

Secure EN 47649 bridge  (5) with safety pins (2).

9. When tool assemble EN 47650 frame and EN 47649 bridge is under load, adjust complete assemble and retighten ALL fasteners.

Note: Secure chain boxes with hook chains on the outside of engine bride.

1. Remove EN 47649 bridge  (5) with the aid of an assistant.

Remove safety pins (2).

Note: EN 47650-050 rail is equipment of EN 47650 frame and enclosed in the EN 47650 frame tool kit.

2. Remove EN 47650-050 rail  (4) from EN 47650 frame .

Remove safety pins (3).




3. Remove front side of EN 47650 frame :

•	Loosen the bolts from clamping piece (3).

•	Loosen the hook (1) with thumb wheel (2) an turn the hook 90° from upper tie bar.




4. Loosen rear side of EN 47650 frame :

4.1.	Loosen EN 47650 frame from EN 47650-300 adapters with mounting bolts (1).

4.2.	Remove safety pins (2) from the EN 47650-300 adapters and the side bars.




5. With the aid of an assistant remove EN 47650 frame  (1) from the vehicle.



6. Remove EN 47650-300 adapter  (1) from front compartment rail.



7. Clean contact surfaces (1) from EN 47650 frame on the upper tie bar with solvent.
8. Install the front fender shipping cover. Refer to Front Fender Shipping Cover Replacement .