Orlando |
||||||||
|
|
|
|||||||
| Table 1: | Body Control Module Scan Tool Data Parameters |
| Table 2: | Body Control Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Definition |
|---|---|---|---|
Operating Conditions: Ignition ON, Vehicle in Park, All Doors Closed | |||
5 V Ignition Switch | - | Accessory / Key Out | The scan tool displays Off, Accessory, Run, or Crank. This parameter displays the ignition switch mode. |
Accent Lighting 1 Command | -- | Varies | This parameter displays the interior lighting ambient 1 command as a percentage. |
Accessory | -- | Active | The scan tool displays Active or Inactive. |
Accessory Power Mode Indicator Command | -- | Varies | This parameter displays ignition switch accessory LED PWM command as a percentage. |
Accessory Relay Command | -- | Active | The scan tool displays Active or Inactive. |
Accessory/Retained Accessory Power Relay Command | -- | Active | The scan tool displays Active or Inactive. This parameter displays the retained accessory power relay status. |
All Door Lock Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the door lock status. |
Ambient Light Sensor | -- | Varies | The scan tool displays volts. This parameter displays the ambient light sensor signal voltage. |
Ambient Light Status | -- | Night | The scan tool displays Unknown, Night, or Day. This parameter displays the ambient light level status. |
Automatic Headlamps Disable Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the headlamp disable switch status. |
Automatic Transmission Manual Shift Switch | -- | Off | The scan tool displays Off or On. This parameter displays the transmission tap up tap down switch status. |
Reverse Lamps Relay Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the reverse lamps relay status. |
Battery Low at Start | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays Active when the battery level is low when the vehicle starts. |
Battery Reconnect Detected | -- | No | The scan tool displays No or Yes when a battery disconnect/reconnect event has been detected. |
Battery Voltage | -- | Varies | The scan tool displays the current battery voltage. |
BCM-Controlled Charging Voltage | -- | Active | The scan tool displays Active or Inactive. |
BCM-Requested Charging Voltage Reduction | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays Active when the BCM has detected a low battery voltage condition. |
Boot Software Part Number | -- | Varies | The scan tool displays the boot software part number. |
Brake Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the brake lamp command status. |
Brake Pedal Initial Travel Position Achieved | -- | No | The scan tool displays No or Yes. |
Brake Pedal Position Sensor High Voltage During Learn | -- | No | The scan tool displays No or Yes. |
Brake Pedal Position Sensor Learn | -- | No | The scan tool displays No or Yes. This parameter displays Yes when the brake pedal position sensor has learned. |
Brake Pedal Position Sensor Learned Home Position | -- | Yes | The scan tool displays No or Yes. This parameter displays Yes when the brake pedal position sensor has learned the home position. |
Brake Pedal Position Sensor Low Voltage During Learn | -- | No | The scan tool displays No or Yes. |
Brake Pedal Position Sensor Move During Learn | -- | No | The scan tool displays No or Yes. This parameter displays the brake pedal sensor learn status. |
Brake Pedal Position Sensor Pulled Up from Home Position | -- | No | The scan tool displays No or Yes. |
Brake Pedal Position Sensor Reference | -- | Varies | The scan tool displays the brake pedal position as voltage value. This parameter displays the current brake pedal position sensor reference. |
Brake Pedal Pulled Up from Home Position | -- | No | The scan tool displays No or Yes. |
Brake Transmission Shift Interlock Solenoid Actuator | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the remote start diagnostic status history. |
Brake Transmission Shift Interlock Solenoid Actuator Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the last remote start diagnostic status history. |
Calibration Part Number 1-20 | -- | Varies | The scan tool displays the software module calibration part number. |
Centre Brake Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the centre brake lamp status. |
Central Door Lock Switch on Center Console | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver door lock switch status. |
Child Security Lock Indicator Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the child security lock indicator command status. |
Content Theft Deterrent Alarm Status | -- | Disarmed | The scan tool displays Off, Armed, or Disarmed. This parameter displays the content theft alarm status. |
Content Theft Deterrent Disarmed Until Vehicle Closed | -- | No | The scan tool displays No or Yes. This parameter displays the content theft deterrent system status. |
Content Theft Deterrent Mode | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Content Theft Deterrent Trigger History 1-3 | -- | None | The scan tool displays None, Driver door, Passenger door, Left rear door, Right rear door, Rear closure, Midgate, Tonneau Cover, Bonnet, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorised PWM change, Security Indicates Tamper, or Glass Breakage. This parameter displays the content theft deterrent trigger history status. |
Courtesy Lamps Duty Cycle Command | -- | Varies | This parameter displays the interior lights dimming command as a percentage. |
Crank Abort | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Cruise Charging Set Level | -- | Varies | This parameter displays cruise charging set level. |
Cruise Control Switch Status | -- | OFF | The scan tool displays CANCEL, OFF, ON, RESUME, SET or ERROR. This parameter displays the cruise control switch status. |
Current Content Theft Deterrent Trigger | -- | None | The scan tool displays None, Driver door, Passenger door, Left rear door, Right rear door, Rear closure, Midgate, Tonneau Cover, Bonnet, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorised PWM change, Security Indicates Tamper, Glass Breakage. This parameter displays the content theft deterrent current alarm trigger. |
Current Driver | - | 1-8 | This parameter displays the current driver in vehicle. |
Disable Battery Saver Relay Command | -- | Inactive | The scan tool displays Active or Inactive. |
Interior light Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the interior light switch status. |
Driver Door Ajar Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver door Ajar switch status. |
Driver Door Unlock Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver door unlock command status. |
Driver Window Learned | -- | Yes | The scan tool displays No or Yes. |
Driver Window Main Control Down Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver window main control down switch input status. |
Driver Window Main Control Express Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver window switch express input status. |
Driver Window Main Control Up Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the driver window switch UP input status. |
Driver Window Motor Mode | - | Local Switch Overridden | The scan tool displays Down, Express Down, Express, Up, Error, Inhibit, or Local Switch Overridden. This parameter displays the driver window motor mode status. |
Enable Battery Saver Relay Command | -- | Inactive | The scan tool displays Active or Inactive. |
End Model Part Number | -- | Varies | This parameter displays the end model part number. |
Engine Stalled | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Environment Identification | - | Unknown | The parameter displays the vehicle environment identification successful status. |
Environment Identification | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the front fog lamps status. |
Front Fog Lamps Relay Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the front fog light relay status. |
Front Fog Lamps Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the front fog lamp switch status. |
Front Passenger Window Main Control Down Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the front passenger window down switch status. |
Front Passenger Window Main Control Express Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger window switch express input status. |
Front Passenger Window Main Control Up Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger window switch UP input status. |
Front Tyre Pressure on Placard | -- | Varies | The scan tool displays kPa or PSI. This parameter displays the specified tyre pressure placard information programmed in the BCM for tyre pressure monitoring. |
Fuel Economy Mode Inhibited - Low Charging Voltage | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the fuel economy mode status. |
Generator Regulator Setpoint | -- | Varies | The scan tool displays percentage. |
Hazard Lamps Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the hazard lamps switch status. |
Hazard Lamps Switch Backlight Command | -- | Varies | The scan tool displays percentage. This parameter displays hazard switch backlight level PWM command status. |
Headlamps On Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the headlamp on switch status. |
Headlamps Flash Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the headlamps flash to pass switch status. |
High Beam Select Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the main beam switch status. |
High Beam Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the main beam command status. |
Bonnet Ajar Switch | -- | Inactive | This parameter display the remote start diagnostic status history or the last remote start diagnostic status history. |
Bonnet Ajar Switch Signal 1 | -- | Inactive | This parameter display the remote start diagnostic status history or the last remote start diagnostic status history. |
Bonnet Position | - | CLOSED | The scan tool displays CLOSED, AJAR, or OPENED. This parameter displays the bonnet position. |
Horn Relay Command | -- | Inactive | The scan tool displays Active or Inactive. |
Horn Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Idle Boost Level 2-3 Counter | -- | Varies | This parameter displays the state of the idle boost level as counts. |
Idle Charging Set Level | -- | Varies | This parameter displays idle charging set level. |
Ignition Mode Switch Dimming Command | -- | Varies | The scan tool displays as a percentage. |
Ignition Switch Reference | -- | Varies | This parameter displays the ignition switch voltage reference. |
Ignition Switch Signal Voltage | -- | Varies | This parameter displays the ignition switch signal voltage. |
Ignition Switch Status | -- | Inactive | This parameter displays the ignition switch status. |
Immobiliser Allows Engine To Start | - | Unknown | The scan tool displays Unknown, Incorrect, Not Allowed, or Valid. This parameter displays the immobiliser status. |
Immobiliser Automatic Learn Timer | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the automatic learn timer status. |
Immobiliser Environment Device 1-4 | - | Unknown | The scan tool displays Incorrect, Correct, Not Received, Not Programmed or Unknown. This parameter displays the immobiliser source status. |
Immobiliser Password Learn | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the password learn status. |
Immobiliser Password Learn Scan Tool Delay | -- | Varies | This parameter displays the auto learn timer status. |
Immobiliser Security Code Accepted | -- | No | The scan tool displays No or Yes. |
Immobiliser Security Code Lockout | -- | No | The scan tool displays No or Yes. |
Immobiliser Security Code Programmed | -- | Yes | The scan tool displays No or Yes. |
In Park Switch Status | -- | On | The scan tool displays On or Off. This parameter displays the park switch status. |
Inadvertent Load Command | -- | Active | The scan tool displays Active or Inactive. |
Indicator Dimming Duty Cycle Command | -- | Varies | The scan tool displays percentage. This parameter displays indicator lighting PWM command status. |
Interior/Courtesy Lighting Master Switch | - | Door | The scan tool displays Door or other lighting switch status. |
Interior Boot Lid/Tailgate Window Unlatch Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Key Capture Solenoid Actuator | -- | Active | The scan tool display Active or Inactive. This parameter displays column lock input status. |
Key Fob 1-4 Battery Status | -- | OK | The scan tool displays OK or other key fob battery status. This parameter displays the key fob battery status. |
Key Fob 1-4 Function | - | Undefined | The scan tool displays Inactive, Lock, Unlock Driver Door, All Door Unlock, Release Rear Closure, Actuate Left Sliding Door, Actuate Right Sliding door, Panic Alarm, Release Fuel door, Actuate Power Windows, Actuate Folding Top, Start Engine, Stop Engine, Programmed, Locator Alarm, Close Liftgate, Open Liftgate, Stop Liftgate While Closing, Stop Liftgate While opening, Deadlock All Doors, Stop Liftgate Motion, Start Liftgate Motion, Stop Left Sliding Door Motion, Stop Right Sliding Door Motion, Comfort open, or Comfort close. This parameter displays the key fob function status. |
Key Fob in Vehicle | -- | Inactive | This parameter displays the current key fob in the vehicle. |
Key In Cylinder Switch | -- | Active | The scan tool displays Active or Inactive. |
Key In Cylinder Switch/Key Fob in Vehicle | -- | Yes | The scan tool displays No or Yes. |
Key in Ignition Status | -- | Inactive | The scan tool displays Key Out or Key In. This parameter displays the key in ignition status. |
Key Part Number | -- | Varies | This parameter displays the key part number. |
Key Type | - | Master Key | The scan tool displays Unknown, Master Key, Valet Key, Fleet Key, or Unconfigured. This parameter displays the key type. |
Last Door Lock Function | - | All Doors Lock | The scan tool displays NO Action, PC UNDB Lock, PC Unlock, Unlock, Unlock Driver, Unlock Passenger, Unlock Left Rear, Unlock Right Rear, Unlock Cargo Liftgate, Unlock Driver Side, Unlock Passenger Side, Unlock Non Driver, Unlock All, Lock All, DBL Lock, or UNDBL Lock. |
LED Backlight Dimming Command | -- | Varies | The scan tool displays as a percentage. This parameter displays LED backlight dimming PWM command status. |
Left Brake Lamp Command | -- | Varies | The scan tool displays percentage. This parameter displays left brake lamp command status. |
Left Dedicated Daytime Running Lamp Command | -- | Varies | The scan tool displays percentage. This parameter displays left dedicated daytime running lamp command status. |
Left Front Tire Pressure | -- | Varies | This parameter displays left front tyre pressure in PSI. |
Left Front Tire Pressure Identification | -- | Varies | This parameter displays left front tire pressure sensor ID. |
Left Front Tyre Pressure Sensor Location Learned | -- | Yes | The scan tool displays No or Yes. This parameter display tire pressure monitor system learned status. |
Left Front Tyre Pressure Sensor Mode | - | Learn Mode -- Pressure Triggered | The scan tool parameter displays Learn Mode, Undefined, Remeasure Data Mode, Rolling Mode, Enter Off Mode, Exit Off Mode, or Learn Mode Pressure Triggered. |
Left Front Tyre Pressure Status | - | Normal | The scan tool displays Unknown, Normal, Very Low Pressure, Low, Weak Signal, or High. |
Left Front Indicator Bulb Out Feedback | -- | Inactive | The scan tool displays Active or Inactive. |
Left Front Turn Signal/Hazard Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. |
Left Dipped Beam/Daytime Running Light Command | -- | Varies | The scan tool displays percentage. This parameter displays left dipped beam/daytime running lamp status. |
Left Park Lamps Command | -- | Varies | The scan tool displays percentage. This parameter displays rear exterior lighting status. |
Left Rear Door Ajar Switch | -- | Inactive | This parameter displays Active or Inactive. This parameter displays the left rear door ajar switch status. |
Left Rear Tire Pressure | -- | Varies | This parameter displays left rear tyre pressure in PSI. |
Left Rear Tire Pressure Identification | -- | Varies | This parameter displays left rear tire pressure sensor ID. |
Left Rear Tyre Pressure Sensor Location Learned | -- | Yes | The scan tool displays No or Yes. This parameter displays tire pressure monitor system learned status. |
Left Rear Tyre Pressure Sensor Mode | - | Stationary | The scan tool displays Learn Mode, Undefined, Remeasure Data Mode, Rolling Mode, Enter Off Mode, Exit Off Mode, or Learn Mode Pressure Triggered. |
Left Rear Tyre Pressure Status | - | Normal | The scan tool displays Unknown, Normal, Very Low Pressure, Low, Weak Signal, or High. |
Left Rear Indicator Bulb Out Feedback | -- | Inactive | The scan tool displays Active or Inactive. The parameter displays turn lamp outage status. |
Left Rear Indicator/Hazard Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. |
Left Rear Window Main Control Down Switch | -- | Inactive | The scan tool display Active or Inactive. This parameter displays driver window switch inputs. |
Left Rear Window Main Control Express Switch | -- | Inactive | The scan tool display Active or Inactive. This parameter displays driver window switch inputs. |
Left Rear Window Main Control Up Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays driver window switch inputs. |
Left Rear Window Motor Mode | - | Local Switch Overridden | The scan tool displays Down, Express, Up, Inhibit, or Local Switch Overridden. |
Left Rear Window Switch at Door | -- | Inactive | The scan tool displays Active or Inactive. |
Left Indicator Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the left indicator switch status. |
Number Plate Lamps Command | -- | Inactive | The scan tool displays Active or Inactive. |
Load Reduction Level 2-3 Counter | -- | Varies | The scan tool display as counts. |
Low Beam Relay Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the headlamp low beam relay status. |
Manufacturers Enable Counter | -- | Varies | This parameter tool displays various counter values. |
Master Keys Learned | -- | Varies | This parameter displays the total number of master keys learned. |
Module Diagnostic Address | -- | Varies | This parameter displays module diagnostic address. |
Number of Key Fobs In Vehicle | - | 1 | This parameter displays the number of fobs located in the vehicle. |
Odometer | -- | Varies | This parameter displays the vehicle mileage. |
Outside Rear View Mirror Courtesy Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays front exterior lighting status. |
Park Brake Switch | -- | Active | The scan tool displays Active or Inactive. This parameter displays front exterior lighting status. |
Park Lamps Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays Active when the parklamp switch is activated. |
Passenger Door Ajar Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger door ajar switch status. |
Passenger Door Lock Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger door lock switch status. |
Passenger Door Unlock Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger door unlock switch status. |
Passenger Door(s) Unlock Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger door unlock status. |
Passenger Window Learned | -- | Yes | The scan tool displays No or Yes. This parameter displays the passenger window learned status. |
Passenger Window Motor Mode | - | Local Switch Overridden | The scan tool displays Down, Express, Up, Inhibit, or Local Switch Overridden. |
Passenger Window Switch at Door | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the passenger window switch status. |
Previous Key Type | - | Unknown | This parameter displays previous driver identification device type. |
Primary Key Status | -- | Yes | The scan tool displays No or Yes. |
Push Button Ignition Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Push Button Ignition Switch Voltage | -- | Varies | This parameter displays the push button ignition switch voltage. |
Rear Closure Ajar Switch | -- | Active | The scan tool displays Active or Inactive. |
Rear Closure Cylinder Lock Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Rear Closure Cylinder Unlock Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Rear Tyre Pressure on Placard | -- | Varies | This parameter displays the rear tyre pressure in kPa or PSI. This parameter displays the specified tyre pressure placard information programmed in the BCM for tyre pressure monitoring. |
Regulated Voltage Control Mode | - | Voltage | The scan tool displays voltage. |
Remote Vehicle Start Attempts Exhausted | -- | Varies | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history or remaining start attempts. |
Remote Vehicle Start Crank Time | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Remote Vehicle Start Disabled by Driver | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Remote Vehicle Start Source | - | Ignition Switch Start | The scan tool displays Body Control module or Power Take-off Start. |
Remote Vehicle Starts Exhausted | -- | Varies | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history or remaining remote starts. |
Right Brake Lamp Command | -- | Varies | The scan tool display percentage. This parameter displays right brake lamp PWM command status. |
Right Dedicated Daytime Running Lamp Command | -- | Varies | The scan tool display percentage. This parameter displays right dedicated DRL PWM command status. |
Right Front Tire Pressure | -- | Varies | This parameter displays right front tyre pressure in PSI. |
Right Front Tire Pressure Identification | -- | Varies | This parameter displays right front tire pressure sensor ID. |
Right Front Tyre Pressure Sensor Location Learned | -- | Yes | The scan tool displays No or Yes. |
Right Front Tyre Pressure Sensor Mode | - | Stationary | The scan tool displays Learn Mode, Undefined, Remeasure Data Mode, Rolling Mode, Enter Off Mode, Exit Off Mode, or Learn Mode Pressure Triggered. |
Right Front Tyre Pressure Status | - | Normal | The scan tool displays Unknown, Normal, Very Low Pressure, Low, Weak Signal, or High. |
Right Front Indicator Bulb Out Feedback | -- | Inactive | The scan tool displays Active or Inactive. |
Right Front Turn Signal/Hazard Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. |
Right Dipped Beam/Daytime Running Light Command | -- | Varies | The scan tool displays percentage. This parameter displays right dipped beam/daytime running lamp status. |
Right Park Lamps Command | -- | Varies | The scan tool displays percentage. This parameter displays rear exterior lighting status. |
Right Rear Door Ajar Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Tire Pressure | -- | Varies | This parameter displays right rear tyre pressure in PSI. |
Right Rear Tire Pressure Identification | -- | Varies | This parameter displays right rear tire pressure sensor ID. |
Right Rear Tyre Pressure Sensor Location Learned | -- | Yes | The scan tool displays No or Yes. |
Right Rear Tyre Pressure Sensor Mode | - | Learn Mode -- Pressure Triggered | The scan tool displays Learn Mode, Undefined, Remeasure Data Mode, Rolling Mode, Enter Off Mode, Exit Off Mode, or Learn Mode Pressure Triggered. This parameter displays the pressure sensor mode status. |
Right Rear Tyre Pressure Status | - | Normal | The scan tool displays Unknown, Normal, Very Low Pressure, Low, Weak Signal, or High. This parameter displays the right rear tyre pressure status. |
Right Rear Indicator Bulb Out Feedback | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Indicator/Hazard Lamp Command | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Window Main Control Down Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Window Main Control Express Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Window Main Control Up Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Right Rear Window Motor Mode | - | Local Switch Overridden | The scan tool displays Down, Express, Up, Inhibit, or Local Switch Overridden. |
Right Rear Window Switch at Door | -- | Inactive | The scan tool displays Active or Inactive. |
Right Indicator Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the right indicator switch status. |
Run Abort | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Run Relay Command | -- | Active | The scan tool displays Active or Inactive. |
Run/Crank | -- | Inactive | The scan tool displays Active or Inactive. |
Run/Crank Relay Command | -- | Active | The scan tool displays Active or Inactive. |
Run/Start Power Mode Indicator Command | -- | Varies | The scan tool displays percentage. This parameter displays ignition switch run LED PWM command status. |
Secondary Key Status | -- | No | The scan tool displays No or Yes. |
Security Indicator Command | -- | Varies | The scan tool displays percentage. This parameter displays security LED PWM command status. |
Selected Front Tyre Type | - | Standard Load | The scan tool displays No Tyre Type, Metric Standard Load, Metric Extra Load, Load Range C, Load Range D, or Load Range E. This parameter displays the front tyre type. |
Selected Rear Tyre Type | - | Standard Load | The scan tool displays No Tyre Type, Metric Standard Load, Metric Extra Load, Load Range C, Load Range D, or Load Range E. This parameter displays the rear tyre type. |
Start-Up State of Charge | -- | Varies | The scan tool displays percentage. This parameter displays startup state of charge status. |
State of Charge | -- | Varies | The scan tool displays percentage. This parameter displays state of charge status. |
Sunroof Enabled | -- | Active | The scan tool displays Active or Inactive. |
Sunroof Motor Overtemperature | -- | Inactive | The scan tool displays Active or Inactive. |
Sunroof Not Learned | -- | Inactive | The scan tool displays Active or Inactive. |
Sunroof Position | - | Closed | The scan tool displays Closed, Open, Venting, Comfort Open, Closing, Opening. This parameter displays the current sunroof position. |
Sunroof Remote Command | -- | Inactive | The scan tool displays Sunroof Secure Close, Venting, Close, or Open. This parameter displays the last sunroof remote command. |
Sunroof Slide Switch | -- | Inactive | The scan tool displays Inactive, Express Open, Open, Express Close, Close, Short to Ground, Short to Battery, or Stuck. This parameter displays the sunroof slide switch status. |
Sunroof Slide Switch | -- | Inactive | The scan tool displays Inactive, Open, Close, Short to Ground, Short to Battery or Stuck. This parameter displays the sunroof tilt switch status. When the switch experiences a malfunction Short to Ground, Short to Battery or Stuck will be displayed. |
Sunroof/Sunshade Motor Overtemperature | -- | Inactive | The scan tool displays Active or Inactive. |
Sunroof / Sunshade Switch | -- | Inactive | The scan tool displays Inactive, Express Open, Open, Express Close, Close, Short to Ground, Short to Battery, or Stuck. This parameter displays the sunroof or sunshade switch status. |
Sunshade Enabled | -- | Active | The scan tool displays Active or Inactive. |
Sunshade Not Learned | -- | Inactive | The scan tool displays Active or Inactive. |
Sunshade Position | - | Closed | The scan tool displays Ajar, Closed, Opened, Closing, or Opening. This parameter displays the sunshade position status. |
Sunshade Remote Command | -- | Inactive | The scan tool displays Close or Open. This parameter displays the last sunshade remote command. |
Tamper Status | -- | No | The scan tool displays No or Yes. |
Telematics Enhanced Service Override Active | -- | No | The scan tool displays No or Yes. This parameter displays vehicle theft deterrent system status. |
Total Keys Learned | -- | Varies | This parameter displays the number of keys learned. |
Traction Control Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays Active when the traction control switch is active. |
Transponder Authentication | - | Initializing | The scan tool displays Inactive, Initializing, ID Received, Password Received, Data Reception Complete, or Data Transmission Complete. This parameter displays the transponder key communication status. |
Transponder Key Status | -- | OK | The scan tool displays OK, LIN Bus Initialisation Malfunction, Aerial Initialisation Malfunction, Password Error, No Valid Key Detected, LIN Bus Communication Malfunction, or Aerial Malfunction. This parameter displays the transponder key communication error status. |
Trunk Lamp Command | -- | Varies | The scan tool displays as percentage. |
Boot Lid/Tailgate Window Exterior Unlatch Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Trunk Lid/Liftgate Window Unlatch Command | -- | Inactive | The scan tool displays Active or Inactive. |
Valet Keys Learned | -- | Varies | This parameter displays the number of valet keys learned. |
Valet Mode Status | -- | Inactive | This parameter displays the remote start diagnostic status history or the last remote start diagnostic status history. |
Valet switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays Active when the valet switch is on. |
Vehicle Identification Number (VIN) | -- | Varies | This parameter displays the vehicle identification number. |
Window Lockout Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Window Lockout Switch Indicator Command | -- | Inactive | The scan tool displays Active or Inactive. |
Windscreen Washer Relay Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the windscreen washer relay status. |
Windscreen Washer Switch | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the windscreen washer switch status. |
Windscreen Wiper Park Switch | -- | Active | The scan tool displays Active or Inactive. |
Windscreen Wiper High Speed Relay Command | -- | Inactive | The scan tool displays Active or Inactive. |
Windscreen Wiper High Speed Switch | -- | Inactive | The scan tool displays Active or Inactive. |
Windscreen Wiper Motor Relay Command | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the windshield wiper relay status. |
Windscreen Wiper Stalled During Sweep | -- | Inactive | The scan tool displays Active or Inactive. |
Windscreen Wiper Stalled in Park Position | -- | Inactive | The scan tool displays Active or Inactive. This parameter displays the windscreen wiper stalled status. |
Windscreen Wiper Switch | -- | Off | The scan tool displays Off, Delay 1, Delay 2, Delay 3, Delay 4, Delay 5, or Low. This parameter displays the windscreen wiper switch status. |
Scan Tool Output Control | Description |
|---|---|
Accent Lighting 1 Command | The BCM activates the accent lighting when you select On. The value should be 100%. All accent lighting should illuminate until commanded Off. |
Accessory Power Mode Indicator Command | The BCM activates the accessory indicator when you select On. The value should be 100%. The yellow LED accessory indicator on start button should illuminate until commanded Off. |
Accessory/Retained Accessory Power Relay Command | The BCM actuates the retained accessory power relay when you select On. The retained accessory power relay should turn on allowing specific vehicle functions to operate. |
All Doors Lock Command | The BCM activates all doors lock when you select Lock. All doors should lock. |
Reversing Lamps Command | The BCM actuates the reverse lamps relay when you select On. The reverse lamps should illuminate until commanded Off. Engine must be running. |
Battery Saver Relay | The BCM activates the battery saver relay when you select Enable. This command sets the low power mode relay in the state in which it does not supply power to the non-essential parts of the vehicle. This is used to prevent the battery from being depleted when the vehicle is not used for a long period of time. |
Brake Pedal Position Sensor Learn | The BCM activates the brake pedal position sensor learn when you select Learn. The brake pedal position sensor learn procedure should start. |
Centre Brake Lamp Command | The BCM activates the centre brake lamp when you select On. The centre brake lamp should illuminate until commanded Off. |
Child Security Lock Motors Command | The BCM actuates the child security door motor when you select Lock. The child security doors should lock. |
Clear Driver Window Learned Values | When you select Clear the clear driver window learn procedure should start. |
Clear Passenger Window Learned Values | When you select Clear the clear left rear window learn procedure should start. |
Courtesy Lamps Command | The BCM activates the courtesy lamps when you select On. The value should be 100%. The courtesy lamps should illuminate until commanded Off. |
Driver Door Unlatch Command | The BCM activates the output circuit to unlatch the driver door with a passive entry passive start when you select Unlatch. There is NO door handle on this type of vehicle to open the door. Instead, there is a pad that you press to unlatch the door. |
Driver Door Unlock Command | The BCM pulses the driver door unlock motor when you select Unlock. The driver door should unlock. |
Driver Window Motor Mode | The BCM activates the driver window motor when you select Up/Down/Stop/Express Up/Express Down. The driver window should follow the appropriate command. |
Front Fog Lamps Command | The BCM actuates the front fog lamps relay when you select On. The front fog lamps relay should turn on. |
Hazard Lamps Switch Backlight Command | The BCM activates the hazard lamps switch when you select On. The value should be 100%. The hazard lamps switch backlight should illuminate until commanded Off. |
High Beams | The BCM activates the high beam command when you select On. The high beam lights should illuminate. The headlamps have to be on. |
Horn Relay | The BCM activates the horn when you select On. The horn should sound. |
Inadvertent Load Command | The BCM activates the inadvertent load command when you select On. (It is an electronic request to shut down an electrical or electronic device that is drawing power from the battery at a time when there should be no activity, usually after the key has been removed from the ignition for a period of time.) |
LED Backlight Dimming Command | The BCM activates the LED backlight dimming when you select On. The values should be 100%. The LED backlight dimming for control switches should illuminate until commanded Off. |
Left Brake Lamp Command | The BCM activates the left brake lamp when you select On. The values should be 100%. The left brake lamp should illuminate until commanded Off. |
Left Dedicated Daytime Running Lamp Command | The BCM activates the left dedicated daytime running lamp when you select ON. The value changes to 100%. The left daytime running lamp should illuminate. |
Left Front Indicator Lamp Command | The BCM activates the left front indicator lamp when you select On. The left front indicator lamp should illuminate until commanded Off. |
Left Park Lamps Command | The BCM activates the left park lamps when you select ON with a value of 100%. The left park lamps should illuminate. |
Left Rear Indicator Lamp Command | The BCM activates the left rear indicator lamp when you select On. The left rear indicator lamp should illuminate until commanded Off. |
Left Rear Window Motor | The BCM activates the left rear window motor when you select Up/Down/Stop/Express Down. The left rear window should follow the appropriate command. |
Number Plate Lamps Command | The BCM activates the license plate lamps when you select On. The license plate lights should turn on until commanded Off. |
LIN Bus Device Identification Data | When you select Update the LIN Bus Device part number and calibration part number should be updated. |
Low Beam Relay Command | The BCM activates the dipped beams when you select On. The dipped beam lights should turn on. |
Outside Rear View Mirror Courtesy Lamp Command | The BCM activates the outside rear view mirror courtesy lamp when you select On. The outside rear view mirror courtesy lamp (at the bottom) should illuminate. |
Passenger Door(s) Unlatch Command | The BCM activates the output circuit to unlatch the passenger door with a passive entry passive start when you select Unlatch. There is NO door handle on this type of vehicle to open the door. Instead, there is a pad that you press to unlatch the door. |
Passenger Door(s) Unlock Command | The BCM pulses the passenger door unlock motor when you select Unlock. The passenger door should unlock. |
Passenger Window Motor | The BCM activates the passenger window motor when you select Up/Down/Stop/Express Up/Express Down. The passenger window should follow the appropriate command. |
Right Brake Lamp Command | The BCM activates the right brake lamp when you select On. The value should be 100%. The right brake lamp should illuminate until commanded Off. |
Right Dedicated Daytime Running Lamp Command | The BCM activates the right dedicated daytime running lamp when you select On. The value should be 100%. The right daytime running lamp should illuminate. |
Right Front Indicator Lamp Command | The BCM activates the right front indicator lamp when you select On. The right front indicator/hazard lamp should illuminate. |
Right Park Lamps Command | The BCM activates the right park lamps when you select ON with a value of 100%. The right park lamps should illuminate. |
Right Rear Indicator Lamp Command | The BCM activates the right rear indicator/hazard lamp when you select On. The right rear indicator lamp should illuminate until commanded Off. |
Right Rear Window Motor | The BCM activates the right rear window motor when you select Up/Down/Stop/Express Down. The right rear window should follow the appropriate command. |
Run Relay Command | The BCM actuates the run relay when you select On. The run relay should turn on. |
Run/Crank Relay Command | The BCM actuates the run/crank relay when you select On. The run/crank relay should turn on. |
Run/Start Power Mode Indicator Command | The BCM activates the run/start lamp when you select On. The value should be 100%. The green LED on engine start/stop button should illuminate until commanded Off. |
Security Indicator Command | The BCM activates the security indicator command when you select On. The security indicator at center of dash (or at DRL sensor) should illuminate until commanded Off. |
Tyre Pressure Sensors Learn | The BCM activates the tire pressure sensor learn procedure when you select Learn. |
Tire Type/Pressure Selection | When you select OK, you can change tire type and load range. |
Transmission Range Indicator | The BCM activates the transmission range indicator when you select On. The transmission range indicator at the shifter should illuminate until commanded Off. |
Trunk Lamp Command | The BCM activates the trunk lamp when you select On. The value should be 100%. The trunk lamp should illuminate until commanded Off. |
Trunk Lid/Liftgate Window Unlatch Command | The BCM actuates the rear compartment lid release actuator when you select Unlatch. The trunk or liftgate should open. |
Windscreen Washer Relay Command | The BCM actuates the windscreen washer relay when you select On. The windscreen washer relay should turn on. |
Windscreen Wiper High Speed Relay Command | The BCM actuates the windscreen wiper high speed relay when you select On. The windscreen wiper high speed relay should turn on. |
Windscreen Wiper Motor Relay Command | The BCM actuates the windscreen wiper motor relay when you select On. The windscreen wiper motor relay should turn on. |
| © Copyright Chevrolet. All rights reserved |
