Orlando |
||||||||
|
|
The exterior lighting system consists of the following lamps if equipped:
• | Headlamps |
• | Daytime Running Lamps (DRL) |
• | Front fog lamps |
• | Rear fog lamps: |
• | Parking, tail and number plate lamps |
• | Indicator lamps |
• | Hazard warning lamps |
• | Repeater lamps |
• | Stop lamps |
• | Reverse lamps |
The headlamps consist of 1 single bulb which provides low and high beam.
The headlamps may be turned ON in 3 different ways:
• | When the headlamp switch is placed in the ON position, for normal operation |
• | When the headlamp switch is placed in the AUTOMATIC LIGHT position, for automatic lamp control |
• | When the headlamp switch is placed in the AUTOMATIC LIGHT position, with the windscreen wipers ON in daylight conditions, after a 6 second delay |
The body control module (BCM) controls the headlamps based on the inputs explained above. When a dipped beam request is received, the BCM supplies a B+ to the dipped beam headlamps, illuminating the dipped beam headlamps. When a main beam request is received, the BCM grounds the headlamp main beam relay control circuit.
Automatic Light is switched ON as default. It can be switched OFF by turning the light switch to OFF position. It will be switched on again by doing so again. The rain/light sensor module will send the actual ambient light state (day/night) to the BCM. If Automatic Light is enabled, BCM will react on the message received from rain/light sensor module by switching ON/OFF dipped beams.
When the dipped beam headlamps are on and the indicator/multifunction switch is momentarily placed in the flash to pass position, ground is applied to the indicator/multifunction switch. The indicator/multifunction switch applies ground to the BCM through the flash to pass switch signal circuit. The BCM then applies ground to the main beam relay control circuit. This energises the main beam relay, closing the switch side contacts of the main beam relay, applying battery voltage to the left and right main beam fuses. Battery voltage is applied from the main beam fuses through the main beam voltage supply circuit to the main beam headlamp assemblies. This causes the main beam headlamps to illuminate at full brightness momentarily or until the flash to pass switch is released.
The daytime running lamps (DRL) function activates the dipped beam lamps. The DRL will operate when the following conditions are met:
By turning the headlamp switch in the OFF position the automatic light function and the DRL will be deactivated.
The ambient light sensor is used to monitor outside lighting conditions. The ambient light sensor provides a voltage signal that will vary between 0.2-4.9 V depending on outside lighting conditions. The HVAC control module provides a low reference ground and 5 V reference signals to the ambient light sensor. The BCM monitors the ambient light sensor signal circuit to determine if outside lighting conditions are correct for either DRL or dipped beam when the headlamp switch is in the AUTOMATIC LIGHT position. In daylight conditions, the BCM will command the DRL ON by applying battery voltage to the left and right DRL lamps (dipped beams). Any function or condition that turns ON the headlamps will cancel DRL operation.
When the DRL function is activated by the BCM the continuously main beam functionality is disabled, the possibility to use the flash to pass function stays active.
The front fog lamp switch signal circuit is grounded momentarily by pressing the front fog lamp switch. The body control module (BCM) energises the front fog lamp relay by applying ground to the front fog lamp relay control circuit. When the front fog lamp relay is energised, the relay switch contacts close and battery voltage is applied through the front fog lamp fuse to the front fog lamp supply voltage circuit which illuminates the front fog lamps.
The rear fog lamp switch signal circuit is grounded through a resistor momentarily by pressing the rear fog lamp switch. The body control module (BCM) energises the rear fog lamp supply voltage circuit which illuminates the rear fog lamp. With the rear fog lamp switch activated the BCM sends a message via serial data to the instrument cluster requesting the instrument cluster to illuminate the rear fog indicator.
The parking lights, tail lamps and number plate lights are turned ON when the headlamp switch is placed in the PARK LIGHT or DIPPED BEAM position or anytime the headlamps are requested. When the BCM receives a request from the headlamp switch to turn ON the park lamps the BCM sends out a PWM signal, which illuminates the park lamps, tail lamps and number plate lights.
Ground is applied at all times to the indicator/multifunction switch. The indicator lamps may only be activated with the ignition switch in the ON or START position. When the indicator/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the BCM through either the right or left indicator switch signal circuit. The BCM then applies a pulsating voltage to the front and rear indicator lamps through their respective voltage supply circuits. When a indicator request is received by the BCM, a serial data message is sent to the instrument cluster requesting the respective indicator indicator be pulsed ON and OFF.
The repeater lamps are located in the front wing. The repeater lamps are used as additional indicator lamps, and operate as described in the Indicator/Hazard Flasher Lamps description.
The hazard flashers may be activated in any power mode. The hazard switch is permanently grounded. When the hazard switch is placed in the ON position, ground is applied through the hazard switch signal circuit to the BCM. The BCM supplies battery voltage to all indicator lamps in an ON and OFF duty cycle. When the hazard switch is activated, the BCM sends a serial data message to the instrument cluster requesting both indicator indicators to be cycled ON and OFF.
The brake pedal position (BPP) sensor is used to sense the action of the driver application of the brake pedal. The BPP sensor provides an analogue voltage signal that will increase as the brake pedal is applied. The BCM provides a low reference signal and a 5 V reference voltage to the BPP sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the stop lamp control circuit and centre high mounted stop lamp control circuit. When the control circuit is energised the stop lamps are illuminated.
When the transmission is placed in the reverse position, the engine control module (ECM) sends a serial data message to the BCM. The message indicates that the gear selector is in the reverse position. The BCM applies battery voltage to the reverse lamps. The reverse lamps are permanently grounded. Once the driver moves the gear selector out of the reverse position, a message is sent by the ECM via serial data requesting the BCM to remove battery voltage from the reverse lamp control circuit.
To provide battery run down protection, the exterior lamps will be deactivated automatically under certain conditions. The BCM monitors the state of the headlamp switch. If the park or headlamp switch is ON when the ignition switch is placed in either the CRANK or RUN position and then placed in the OFF position, the BCM initiates a 10 min timer. At the end of the 10 min, the BCM will turn off the control power output to the park and headlamp relay coils, deactivating the exterior lamps. This feature will be cancelled if any power mode other than OFF becomes active. The BCM will disable battery run down protection if any of the following conditions exist. The park or headlamp switch is placed in the ON to OFF position, and back to the ON position during battery run down protection. The BCM determined that the park or headlamp switch was not active when the ignition was turned OFF.
© Copyright Chevrolet. All rights reserved |