To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Seat Belt Indicator Circuit Malfunction - Driver

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Driver Seat Belt Switch Signal

1

2

2

2

-

Driver Seat Belt Switch Low Reference

-

2

2

2

-

1. Indicator will remain ON with seat belt buckled.

2. Indicator will illuminate only for the bulb check.

Circuit/System Description

The driver seat belt switch is a 2-wire switch wired to the inflatable restraint sensing and diagnostic module (SDM) using a signal circuit and a low reference circuit. When the seat belt is unbuckled the switch is closed, and when the seat belt is buckled the switch is open. The SDM sends the status of the driver seat belt via serial data to the instrument panel cluster. After receiving the message, the instrument panel cluster controls the illumination of the driver seat belt indicator.

Reference Information

Schematic Reference

Seat Belt Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Seat Belt System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification
  1. Command the instrument cluster all indicators ON and OFF with a scan tool. The driver seat belt indicator should turn ON and OFF as commanded.
    2. [ARW-LISTFAIL]

  2. If the driver seat belt indicator does not turn ON and OFF as commanded Replace the P16 instrument cluster.

    3. [/ARW-LISTFAIL][ARW-LISTPASS]

  3. If the driver seat belt indicator does turn ON and OFF as commanded

    4. [/ARW-LISTPASS]
  4. Monitor the scan tool Driver Seat Belt Switch parameter while buckling and unbuckling the seat belt. The parameter should display Buckled and Unbuckled when changing seat belt states.
    5. [ARW-LISTFAIL]

  5. If the scan tool Driver Seat Belt Switch parameter does not display Buckled and Unbuckled when changing seat belt states

    Refer to Circuit/System Testing.

    6. [/ARW-LISTFAIL][ARW-LISTPASS]

  6. If the scan tool Driver Seat Belt Switch parameter does display Buckled and Unbuckled when changing seat belt states

    7. [/ARW-LISTPASS]
  7. All OK.

Circuit/System Testing

Note: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.

   • B88D seat belt switch-driver
   • Seat belt switch harness connector
   • K36 SDM
   • SDM wiring harness connector

  1. Ignition OFF. Disconnect the harness connector at the B88D seat belt switch-driver.
  2. Test for less than 5 Ω between the low reference circuit terminal 2 and ground.
    3. [ARW-LISTFAIL]

  3. If 5 Ω or greater

    4. [/ARW-LISTFAIL]
    2.1. Disconnect the X2 harness connector at the K36 SDM.
    2.2. Test for less than 2 Ω in each control circuit end to end.
    [ARW-LISTFAIL]

  4. If 2 Ω or greater, repair the open/high resistance in the circuit.

  5. If less than 2 Ω, replace the K36 SDM.

    6. [/ARW-LISTFAIL][ARW-LISTPASS]

  6. If less than 5 Ω

    7. [/ARW-LISTPASS]
  7. Ignition ON.
  8. Verify the scan tool Driver Seat Belt Status parameter displays Buckled.
    9. [ARW-LISTFAIL]

  9. If the scan tool Driver Seat Belt Status parameter does not display Buckled

    10. [/ARW-LISTFAIL]
    4.1. Ignition OFF. Disconnect the X2 harness connector at the K36 SDM.
    4.2. Test for infinite resistance between the seat belt switch signal circuit terminal 1 and ground.
    [ARW-LISTFAIL]

  10. If less than infinite resistance, repair the short to ground on the circuit.

  11. If less than 2 Ω, replace the K36 SDM.

    12. [/ARW-LISTFAIL] [ARW-LISTPASS]

  12. If the scan tool Driver Seat Belt Status parameter does display Buckled

    13. [/ARW-LISTPASS]
  13. Install a 3 A fused jumper wire between the signal circuit terminal 1 and the low reference circuit terminal 2.
  14. Verify the scan tool Driver Seat Belt Status parameter displays Unbuckled.
    15. [ARW-LISTFAIL]

  15. If the scan tool Driver Seat Belt Status parameter does not display Unbuckled

    16. [/ARW-LISTFAIL]
    6.1. Ignition OFF. Disconnect the X2 harness connector at the K36 SDM. Ignition ON.
    6.2. Test for less than 1 V between the signal circuit and ground.
    [ARW-LISTFAIL]

  16. If 1 V or greater, repair the short to voltage on the circuit.

    17. [/ARW-LISTFAIL]
    6.3. Test for less than 2 Ω in each circuit end to end.
    [ARW-LISTFAIL]

  17. If 2 Ω or greater, repair the open/high resistance in the circuit.

  18. If less than 2 Ω, replace the K36 SDM.

    19. [/ARW-LISTFAIL] [ARW-LISTPASS]

  19. If the scan tool Driver Seat Belt Status parameter does display Unbuckled

    20. [/ARW-LISTPASS]
  20. Replace the B88D seat belt switch-driver.

Component Testing
  1. Ignition OFF. Disconnect the harness connector at the B88D seat belt switch-driver. The B88D seat belt switch-driver in the open position.
  2. Test for infinite resistance between the signal circuit terminal 1 and the low reference terminal 2 at the B88D seat belt switch-driver.
    3. [ARW-LISTFAIL]

  3. If there is not infinite resistance

    Replace the B88D seat belt switch-driver.

    4. [/ARW-LISTFAIL][ARW-LISTPASS]

  4. If there is infinite resistance

    5. [/ARW-LISTPASS]
  5. The B88D seat belt switch-driver in the closed position.
  6. Test for less than 1 Ω between the signal circuit terminal 1 and the low reference terminal 2 at the B88D seat belt switch-driver.
    7. [ARW-LISTFAIL]

  7. If 1 Ω or greater

    Replace the B88D seat belt switch-driver.

    8. [/ARW-LISTFAIL][ARW-LISTPASS]

  8. If less than 1 Ω

    9. [/ARW-LISTPASS]
  9. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Front Seat Belt Buckle Replacement
    • Control Module References for SDM or instrument panel cluster replacement, programming and setup
   


© Copyright Chevrolet. All rights reserved