Service Information

Orlando

DTC C1100

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC C1100 01: Brake Pressure Sensor 2 Short-Circuit to Battery

DTC C1100 02: Brake Pressure Sensor 2 Short-circuit to Ground

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
5V Reference	C1100 02	C1100 01	C1100 01	-
Signal	C1100 02	C1100 01	C1100 01	-
Low Reference	-	C1100 01	--	--

The brake servo unit vacuum sensor measures the vacuum in the brake servo assembly. The electronic brake control module (EBCM) supplies a 5 V reference and a low reference circuit to the brake servo vacuum sensor. The vacuum sensor supplies a voltage signal in relation to the pressure in the brake servo to the EBCM.

Conditions for Running the DTC

Ignition ON

Conditions for Setting the DTC

C1100 01

The EBCM detected a short-circuit to voltage on the vacuum sensor 5 V reference circuit.

C1100 02

The EBCM detected a short-circuit to ground on the vacuum sensor 5 V reference circuit.

Action Taken When the DTC Sets

The brake warning indicator turns ON.

Conditions for Clearing the DTC

•	A current DTC clears when the diagnostic runs and passes.

•	The EBCM will turn OFF the indicator in the next ignition cycle.

Reference Information

Schematic Reference

Hydraulic Brake Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Brake Warning System Description and Operation : With Antilock Brake System

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

Inspect the brake servo vacuum system for damage, leakage and correct installation.

⇒	If damage, leakage or incorrect installation is diagnosed, repair or replace the component.

Ignition OFF, disconnect the harness connector at the B19B Brake Servo Vacuum Sensor.
Test for less than 5 Ω between the low reference circuit terminal 2 and ground.

⇒	If greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K17 Electronic Brake Control Module.

Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground.

⇒	If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K17 Electronic Brake Control Module.

⇒	If less than the specified range, test the 5 V reference circuit for an open/high resistance. If the circuit tests normal, replace the K17 Electronic Brake Control Module.

Ignition OFF, disconnect the harness connector at the K17 Electronic Brake Control Module.
Ignition ON, test for less than 0.3 V between the signal circuit terminal 1 at the B19B Brake Booster Vacuum Sensor harness connector and ground.

⇒	If greater than the specified value, test the signal circuit for a short to voltage.

Ignition OFF, test for infinite resistance between the signal circuit terminal 1 and ground.

⇒	If less than the specified value, test the signal circuit for a short to ground.

Test for less than 5 Ω between the signal circuit terminal 1 at the B19B Brake Servo Unit Vacuum Sensor harness connector and terminal 22 at the K17 Electronic Brake Control Module harness connector.

⇒	If greater than the specified value, test the signal circuit for an open/high resistance.

If all circuits test normal, replace the B19B Brake Servo Vacuum Sensor and verify the DTC does not reset. If the DTC resets, replace the K17 Electronic Brake Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for EBCM replacement, setup and programming