Service Information

Orlando

DTC B2345

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B2345 13: Seat Heater Disable Circuit Low Voltage/High Temperature

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Driver Heated Seat Cushion Temperature Sensor Signal	B1925 02	B1925 05	B1925 05	B2345 13
Passenger Heated Seat Cushion Temperature Sensor Signal	B2170 02	B2170 05	B2170 05	B2345 13
Driver Heated Seat Element Control Terminal 3 X2	B242A 02	B2425 0D	B242A 01	B2425 0E
Driver Heated Seat Element Control Terminal 1 X2	B242A 02	B2425 0D	B242A 01	B2425 0E
Passenger Heated Seat Element Control Terminal 5 X2	B242A 02	B2430 0D	B242A 01	B2430 0E
Passenger Heated Seat Element Control Terminal 2 X2	B242A 02	B2430 0D	B242A 01	B2430 0E
Driver Heated Seat Cushion Temperature Sensor Low Reference	-	B1925 05	-	B2345 13
Passenger Heated Seat Cushion Temperature Sensor Low Reference	-	B2170 05	-	B2345 13

The seat heating control module controls seat heating operation for both the driver and front passenger seats. The heating elements are controlled through individual high side and low side control circuits. The low side control circuits for both seats are connected to a common reference point internal to the module. This reference point is biased to approximately 2.5 V. Before the seat heating control module will allow heated seat operation, it checks to see if this biased voltage is shorted to ground or voltage. Once the module verifies that it is not closing to a shorted heating element, it allows for heated seat operation. The module will then continue to monitor the heating elements for a shorted circuit.

Conditions for Running the DTC

The seat heating control module must be powered.

Conditions for Setting the DTC

B2345 13

Any temperature sensor input that remains below 1.5 V for more than 1 s.

Action Taken When the DTC Sets

The heated seat function for both seats will be disabled.

Conditions for Clearing the DTC

•	The current DTC will clear and set the code to history 3 s after the reference voltage returns to the normal operating range and the ignition is cycled OFF then back to ACCESSORY or RUN.

•	The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.

Reference Information

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

Ignition OFF, disconnect the X2, X3 wiring harness plugs at the K29 Seat Heating Control Module.
Test for greater than 3.0 kΩ between the signal and the low reference circuits listed below:

•	E14B Seat Heating Element - Driver Cushion terminal 3 X3 and terminal 13 X2

•	E14D Seat Heating Element - Passenger Cushion terminal 4 X3 and terminal 14 X2

⇒	If less than the specified value, test for a short between the signal and low reference circuits. If the circuits test normal, replace the appropriate seat cushion heating element.

If all circuits test normal, replace the K29 Seat Heating Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

•	Driver or Passenger Seat Back Cushion Heater Replacement

•	Driver or Passenger Seat Cushion Heater Replacement

•	Control Module References for seat heating control module replacement, setup and programming