To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Power Brake Booster Replacement - Left Hand Drive

Special Tools

CH-558-10 Closure Cap

For equivalent regional tools, refer to Special Tools .

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface section.

Removal Procedure

  1. Turn the ignition to the OFF position.
  2. Remove battery tray. Refer to Battery Tray Replacement .
  3. Remove dash upper extension panel opening cover. Refer to Dash Upper Extension Panel Opening Cover Replacement .

  4. 2027873

    Note: Do NOT disconnect engine coolant hoses.

  5. Remove the radiator surge tank clip (2).
  6. Remove the radiator surge tank (1).
  7. Position the radiator surge tank (1) aside.


    2027346
  8. Remove the brake fluid reservoir cap and install CH-558-10 cap (1) in order to prevent fluid loss and contamination.
  9. Caution: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

  10. Disconnect the electrical connector from the EBCM/EBTCM.

  11. 2027887

    Note: Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  12. Remove the 6 brake pipes (1, 2) from the BPMV.

  13. 2027728

    Note: Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  14. Disconnect the master cylinder secondary brake pipe fitting (1).

  15. 2027729

    Note: Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  16. Disconnect the master cylinder primary brake pipe fitting (1).

  17. 2027887
  18. Remove the BPMV bracket bolts (2).
  19. Remove the BPMV bracket assembly (1).
  20. Remove the brake master cylinder assembly from the booster. Refer to Master Cylinder Replacement : Left Hand Drive → Right Hand Drive .

  21. 2027889
  22. Remove the booster vacuum pipe (1) from the booster.

  23. 2027891
  24. Disconnect the brake pedal pushrod (1) from the brake pedal.

  25. 2192450
  26. Replace click fit connector (1) between servo pushrod and brake pedal with NEW part.

  27. 2027892
  28. Remove the brake booster bolts (1).
  29. Remove the booster from the vehicle.

Installation Procedure


    2027892
  1. Install the booster to the vehicle.
  2. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the brake servo unit bolts (1) and tighten to 19 N·m (14 lb ft).

  4. 2027891
  5. Connect the brake pedal pushrod (1) to the brake pedal.

  6. 2027889
  7. Install the booster vacuum pipe (1) to the booster.
  8. Install the master cylinder assembly to the booster. Refer to  Master Cylinder Replacement : Left Hand Drive → Right Hand Drive .

  9. 2027887
  10. Install the BPMV bracket assembly (1).
  11. Install the BPMV bracket bolts (2) and tighten to 20 N·m (15 lb ft).

  12. 2027729
  13. Connect the master cylinder primary brake pipe fitting (1) and tighten to 18 N·m (13 lb ft).

  14. 2027728
  15. Connect the master cylinder primary brake pipe fitting (1) and tighten to 18 N·m (13 lb ft).

  16. 2027887

    Note: Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  17. Install the 6 brake pipes (1, 2) to the BPMV and tighten to 18 N·m (13 lb ft).
  18. Connect the electrical connector with to the EBCM/EBTCM.

  19. 2027346
  20. Remove the CH-558-10 cap (1) and install the brake fluid reservoir cap.

  21. 2027873
  22. Install the radiator surge tank (1).
  23. Install the radiator surge tank clip (2).
  24. Install the battery tray. Refer to Battery Tray Replacement .
  25. Install dash upper extension panel opening cover. Refer to Dash Upper Extension Panel Opening Cover Replacement .
  26. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .
   


© Copyright Chevrolet. All rights reserved