To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Crankshaft Pulley Replacement

Special Tools

    • EN-470-B Angle Meter
    • EN-48952 Drive Belt Tensioner Holding Pin
    • EN-50432 Adaptor Flywheel Fixing
    • EN-50436 Remover-Crankshaft Pulley Bolt

For equivalent regional tools, refer to Special Tools .

Removal Procedure

  1. Disconnect battery negative cable. Refer to Battery Negative Cable Disconnection and Connection : without Start/Stop System .
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Remove the front compartment insulator. Refer to Front Compartment Insulator Replacement .
  4. Remove the front part of the right front wheelhousing lining. Refer to Front Wheelhouse Liner Replacement .
  5. Remove the drive belt and pulley cover. Refer to Drive Belt and Pulley Cover Removal .

  6. 2506200
  7. Apply tension to the drive belt tensioner (1) with a suitable spanner on the holder (2) by rotating anti-clockwise.
  8. Install the EN-48952 holding pin (3).
  9. Remove the drive belt from the crankshaft pulley.
  10. Remove the starter. Refer to Starter Replacement : 2.4L LAF → 2.0L Diesel LNP with MT → 2.0L Diesel LNP with AT → 1.6L LDE, LXV, 1.8L 2H0, LUW and LFH .

  11. 2506219
  12. Install the EN-50432 flywheel fixing (1) to counterhold the crankshaft.

  13. 2373377
  14. Loosen the crankshaft pulley bolt with the EN-50436 remover (1).

  15. 2373199
  16. Remove and DISCARD the crankshaft pulley bolt (3) and washer (2).
  17. Remove the crankshaft pulley (1).

Installation Procedure


    2373199
  1. Install the crankshaft pulley (1).
  2. Install the NEW crankshaft pulley bolt (3) and washer (2).
  3. Caution: Refer to Fastener Caution in the Preface section.

    Caution: Refer to Torque-to-Yield Fastener Caution in the Preface section.

  4. Tighten the crankshaft pulley bolt (3) in 2 steps.
  5. • First step: 120 N·m (89 lb ft).
    • Second step: +90°. Use EN-470-B meter .
  6. Remove the EN-50432 flywheel fixing .
  7. Install the starter. Refer to Starter Replacement : 2.4L LAF → 2.0L Diesel LNP with MT → 2.0L Diesel LNP with AT → 1.6L LDE, LXV, 1.8L 2H0, LUW and LFH .
  8. Install the drive belt to the crankshaft pulley.

  9. 2506200
  10. Apply tension the drive belt tensioner (1) with a suitable spanner on the holder (2) by rotating anti-clockwise.
  11. Remove the EN-48952 holding pin (3).
  12. Relieve tension from the drive belt tensioner (1) and allow the tensioner to slide back slowly.
  13. Inspect the drive belt for correct seat.
  14. Install the drive belt and pulley cover. Refer to Drive Belt and Pulley Cover Installation .
  15. Install the front part of the right front wheelhousing lining. Refer to Front Wheelhouse Liner Replacement .
  16. Install the front compartment insulator. Refer to Front Compartment Insulator Replacement .
  17. Lower the vehicle.
  18. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection : without Start/Stop System .
   


© Copyright Chevrolet. All rights reserved