To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B3600

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B3600 03: Passenger Compartment Dimming Request Signal Circuit Low Voltage

DTC B3600 07: Passenger Compartment Dimming Request Signal Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

12V Reference

B3600 03

B3600 03

B3600 03**

B1395 07

Instrument Panel Dimming Signal

B3600 03

B3600 03

B3600 07*

-

* Interior Backlighting Inoperative

** Interior Backlighting Cannot be Dimmed

Circuit/System Description

The instrument panel dimmer switch is used to increase and decrease the brightness of the interior backlighting components. The body control module (BCM) supplies a 12 V reference to the backlight dimmer switch, which is part of the headlamp switch. When the backlight dimmer switch is placed in a desired brightness position, reference voltage is applied through the dimmer switch rheostat to the BCM. The BCM interprets this voltage signal, then applies a pulse width modulated (PWM) voltage to the LED dimming control circuit to all related interior lamps, illuminating them to the desired level of brightness.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

    • The BCM detects a short to ground or open in the 12 V reference circuit.
    • The BCM detects a short to ground or open in the instrument panel dimming signal circuit.

Action Taken When the DTC Sets

The Instrument Panel lamps are not illuminated.

Conditions for Clearing the DTC

A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Interior Lights Dimming Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Interior Lighting Systems Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, turn the parking lamps ON, cover the ambient light sensor, vary the interior lamp dimming switch from dim to full bright. The instrument panel lamps should dim and then become full bright.

Circuit/System Testing

  1. Ignition OFF, disconnect the X1 and X3 harness connectors at the K9 Body Control Module.
  2. Ignition ON, test for less than 0.3 V between the signal circuit terminal 9 X1 and ground.
  3. If greater than the specified value, test the circuits listed below for a short to voltage. If the circuit tests normal, replace the S30 Headlamp Switch.
    • Signal circuit terminal 9 X1
    • 12 V reference voltage circuit terminal 4 X3
  4. Ignition OFF, test for infinite resistance between the signal circuit terminal 9 X1 and ground.
  5. If less than infinite resistance, test the circuits listed below for a short to ground. If the circuit tests normal, replace the S30 Headlamp Switch.
    • Signal circuit terminal 9 X1
    • 12 V reference voltage circuit terminal 4 X3
  6. Test for 7.4-7.9 kΩ between the signal circuit terminal 9 X1 and the 12 V reference voltage circuit terminal 4 X3.
  7. If less than 7.4 kΩ, test the signal circuit and the 12 V reference circuit for a short circuit. If the circuit tests normal, replace the S30 Headlamp Switch.
    If greater than 7.9 kΩ, test the signal circuit and the 12 V reference circuit for an open/high resistance. If the circuit tests normal, replace the S30 Headlamp Switch.
  8. Test for 3.7-4.1 kΩ between the signal circuit terminal 9 X1 and the 12 V reference voltage circuit terminal 4 X3 while turning the thumbwheel for dimming up.
  9. If not the specified range, replace the S30 Headlamp Switch.
  10. Test for 5.1-5.5 kΩ between the signal circuit terminal 9 X1 and the 12 V reference voltage circuit terminal 4 X3 while turning the thumbwheel for dimming down.
  11. If not the specified range, replace the S30 Headlamp Switch.
  12. If all circuits test normal, replace the K9 Body Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Headlamp Switch Replacement
    • Control Module References for BCM replacement, setup, and programming
   


© Copyright Chevrolet. All rights reserved