To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B2585 or B3867

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B2585 01: Park Lamps Control Circuit Short to Battery

DTC B2585 02: Park Lamps Control Circuit Short to Ground

DTC B2585 04: Park Lamps Control Circuit Open

DTC B3867 01: Right Parking Light Control Circuit Short to Battery

DTC B3867 02: Right Parking Light Control Circuit Short to Ground

DTC B3867 04: Right Parking Light Control Circuit Open

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Park Lamps Control

B2585 02

B2585 04

B2585 01

-

Right Park Lamp Control

B3867 02

B3867 04

B3867 01

--

Circuit/System Description

The body control module (BCM) energises the park lamps by applying voltage to the park lamp control circuit. When the park lamp control circuit is energised the park lamps are illuminated.

Conditions for Running the DTC

B2585 01

The parking lights are turned OFF.

B2585 02 or B2585 04

The parking lights are turned ON.

B3867 01

    • The ignition is turned OFF.
    • Headlamp switch in OFF or AUTO position.

B3867 02 or B3867 04

Headlamp switch in park or dipped beam position.

Conditions for Setting the DTC

B2585 01 or B3867 01

The BCM detects a short to voltage on the control circuit.

B2585 02 or B3867 02

The BCM detects a short to ground on the control circuit.

B2585 04 or B3867 04

The BCM detects an open control circuit.

Action Taken When the DTC Sets

The park lamps are inoperative.

Conditions for Clearing the DTC

The condition for setting the DTC is not longer present.

Reference Information

Schematic Reference

Exterior Lamps Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, perform the appropriate Tail Lamp test. The appropriate park lamp should be ON/OFF.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the appropriate inoperative tail lamp.
  2. Test for less than 5 Ω between the appropriate tail lamp ground circuit harness connector listed below and ground.
  3. • E5AA Tail/Stop Lamp - Left harness connector terminal 3
    • E5AB Tail/Stop Lamp - Right harness connector terminal 3
    • E4J Park Light - Left Front harness connector terminal 3
    • E4K Park Light - Right Front harness connector terminal 3
    If greater than the specified value, test the ground circuit for an open/high resistance.
  4. Connect a test lamp between the appropriate tail lamp control circuit harness connector listed below and ground.
  5. • E5AA Tail/Stop Lamp - Left harness connector terminal 2
    • E5AB Tail/Stop Lamp - Right harness connector terminal 2
    • E4J Park Light - Left Front harness connector terminal 2
    • E4K Park Light - Right Front harness connector terminal 2
  6. Command the appropriate Tail Lamp test ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  7. If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 Body Control Module.
    If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the K9 Body Control Module.
  8. If all the circuits test normal, replace the appropriate inoperative tail lamp.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Tail Lamp Replacement
    • Control Module References for BCM replacement, setup and programming
   


© Copyright Chevrolet. All rights reserved