Orlando

DTC C0277 or C0890

The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analogue voltage signal that will increase as the brake pedal is applied. The body control module provides a low reference signal and a 5 V reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the stop lamp control circuit and centre high mounted stop lamp control circuit. When the control circuit is energised the stop lamps are illuminated.

C0277 06 or C0890 03

C0277 07 or C0890 07

C0277 09

The DTC will set when the BCM detects the brake pedal position sensor signal is changing faster than possible under normal operating conditions.

C0277 4B

The DTC will set when the brake pedal position sensor home position is not learned.

Brake lights always ON.

The condition for setting the DTC is not longer present.

C0277 4B

If the DTC is set, recalibrate the brake pedal position sensor.

C0277 09

If the DTC is set, replace the brake pedal position sensor. If the DTC resets, replace the BCM.

Schematic Reference

Exterior Lamps Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

C0277 06 or C0277 07

1. Ignition OFF, disconnect the harness connector at the B22 Brake Pedal Position Sensor.
2. Disconnect the negative terminal of the C1 Battery.
3. Ignition OFF, test for less than 5 Ω between the low reference circuit terminal A and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.

4. Reconnect the negative terminal to the C1 Battery.
5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal C and ground.

⇒	If less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.

⇒	If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K9 Body Control Module.

6. Test for less than 0.3 V between the signal circuit terminal B and ground.

⇒	If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K9 Body Control Module.

7. Test for 4.8-5.2 V between the 5 V reference circuit terminal C and the signal circuit terminal B.

⇒	If less than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.

8. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
9. Test for infinite resistance between the signal circuit terminal B and ground.

⇒	If less than the specified range, test the signal circuit for a short to ground.

10. If all circuits test normal, test or replace the B22 Brake Pedal Position Sensor.

C0277 09

1. If the DTC is set, replace the B22 Brake Pedal Position Sensor.
2. Perform the brake pedal position sensor recalibration procedure. Refer to Brake Pedal Position Sensor Calibration
3. Operate the vehicle within the Conditions for Running and Setting the DTC and verify the DTC does not reset.

⇒	If the DTC resets, replace the K9 Body Control Module.

C0277 4B

1. If the DTC is set, recalibrate the B22 Brake Pedal Position Sensor.
2. Verify that the DTC sets under the conditions for running and setting.
3. Perform the brake pedal position sensor recalibration procedure. Refer to Brake Pedal Position Sensor Calibration
4. Operate the vehicle within the Conditions for Running and Setting the DTC and verify the DTC does not reset.

⇒	If the DTC resets, replace the B22 Brake Pedal Position Sensor.

Static Test

1. Ignition OFF, disconnect the harness connector at the B22 Brake Pedal Position Sensor.
2. Test for 2.7-3.2 kΩ between the 5 V reference terminal A and the low reference terminal C.

⇒	If not within the specified range, replace the B22 Brake Pedal Position Sensor.

3. Sweep the sensor through the entire range while monitoring the resistance between the signal terminal B and the low reference terminal A. The resistance should vary between 2.7-3.5 kΩ without any spikes or dropouts.

⇒	If not within the specified range or is erratic, replace the B22 Brake Pedal Position Sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.