To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B389A

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B389A 00: Environment Identification

Circuit/System Description

When certain modules are programmed and configured during installation, the module learns a specific environment identifier which is unique to the vehicle. The environment identifier is used to prevent the swapping of modules between vehicles. The body control module (BCM) is the keeper of the environment identifier. The instrument cluster, electronic brake control module (EBCM), HVAC control module, sensing and diagnostic module (SDM), engine control module (ECM), and steering column lock control module, if equipped, each learn the environment identifier during their configuration process. During vehicle operation, each of these modules compare their environment identifier to that of the BCM. If the identifiers match, vehicle starting is allowed. If an environment identifier does not match, vehicle starting is disabled.

Conditions for Running the DTC

Ignition is in the ACCESSORY or RUN position.

Conditions for Setting the DTC

An incorrect environment identifier is stored by the BCM.

Action Taken When the DTC Sets
    • The security indicator in the instrument cluster will illuminate.
    • Vehicle starting will be disabled.

Conditions for Clearing the DTC

A current DTC will be cleared when the BCM learns a correct environment identifier.

Diagnostic Aids

If BCM programming is not properly completed after BCM replacement, the environment identifier will not be properly learned. If DTC B389A sets immediately after the replacement and programming of a BCM, perform the programming procedure again.

Reference Information

Schematic Reference

Immobiliser Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Immobiliser Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification
  1. Verify DTC B389A did not set immediately following the replacement and programming of a BCM.
    2. [ARW-LISTFAIL]

  2. If the DTC set immediately after the replacement and programming of a BCM

    The immobiliser learn procedure was not properly completed. Perform the BCM immobiliser learn using the Body Control Module IMMO Function with Existing Transponder or Remote Key in SPS. Refer to Immobiliser System Component Programming .

    3. [/ARW-LISTFAIL][ARW-LISTPASS]

  3. If the DTC did not set immediately after the replacement and programming of a BCM

    4. [/ARW-LISTPASS]
  4. Verify DTC B3902 is not set in the any of the control modules listed below:
    5. • ECM
    • SDM
    • EBCM
    • HVAC control module
    • Instrument cluster
    • Steering column lock control module, if equipped
    [ARW-LISTFAIL]

  5. If DTC B3902 is set in any of the modules

    Refer to DTC B3902 .

    6. [/ARW-LISTFAIL][ARW-LISTPASS]

  6. If DTC B3902 is not set in any of the modules

    7. [/ARW-LISTPASS]
  7. Perform the BCM immobiliser learn using Body Control Module IMMO Function with Existing Transponder or Remote Key in SPS. Refer to Immobiliser System Component Programming .
  8. Verify DTC B389A does not set after programming.
    9. [ARW-LISTFAIL]

  9. If the DTC sets after programming

    Replace the K9 BCM.

    10. [/ARW-LISTFAIL][ARW-LISTPASS]

  10. If the DTC does not set after programming

    11. [/ARW-LISTPASS]
  11. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

Control Module References for BCM replacement, programming, and set-up

   


© Copyright Chevrolet. All rights reserved