To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B3205

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B3205 00: Driver Window Motor Circuit

DTC B3205 39: Driver Window Motor Circuit Internal Electronic Failure

DTC B3205 42: Driver Window Motor Circuit Calibration Data Set Not Programmed

DTC B3205 4B: Driver Window Motor Circuit Calibration Not Learned

Circuit/System Description

The body control module (BCM) monitors, receives and transmits serial data to each of the doors switches and window motors. When a window switch has been activated on the driver window switch, a signal is sent to the BCM which sends a signal to the appropriate window motor and the window motor will move in the direction commanded.

Conditions for Running the DTC

    • The ignition switch is in the ON position.
    • Battery voltage must be between 9-16 V.

Conditions for Setting the DTC

B3205 00

The BCM has detected that the compatibility code stored in the driver window motor does not match the compatibility code stored in the BCM.

B3205 39

An internal malfunction has been detected by the BCM in the driver window motor while commanding the window UP or DOWN.

B3205 42

The BCM will automatically attempt to download the calibration program into the driver window motor (As will occur when the window motor has been replaced), if the first calibration program fails to load, the BCM will attempt to download the calibration program a second time. If this download fails, the BCM will set appropriate DTC.

B3205 4B

The BCM has detected that the driver window is not "normalised" and can set for the following reasons:

    • When the battery has been disconnected
    • When the battery has been replaced
    • When the door wiring harness has been disconnected
    • When the window motor has been disconnected.

Action Taken When the DTC Sets

The driver power window will malfunction.

Conditions for Clearing the DTC

B3205 00

Installing a compatible window motor for that specific make and model vehicle.

B3205 39

The driver window motor must be replaced before the DTC can be cleared.

B3205 42

The driver window motor must be replaced before the DTC can be cleared.

B3205 4B

The driver window motor must be normalised before the DTC can be cleared.

Reference Information

Schematic Reference

Moveable Window Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Power Windows Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

B3205 00, B3205 39, B3205 42

  1. Ignition ON, command the driver window UP and DOWN with a scan tool. The driver window should perform the UP and DOWN functions.
  2. Note: If the window performs the UP and DOWN functions, clear the DTC

  3. Replace the M74D window motor--driver with a M74D window motor--driver compatible for that specific make and model vehicle.

Circuit/System Testing

B3205 4B

    Note: The all doors must be completely closed prior to normalizing the windows, a door that is open or ajar may cause the power window to function abnormally or it may become inoperative during the normalization procedure. If this occurs, verify that the door is completely closed then repeat the normalisation procedure.

  1. Ignition ON, starting with the window completely UP, press and hold the driver power window switch until the window is fully open and continue holding the switch down for approximately 5 seconds after the window is completely open.
  2. Pull the power window switch up until the window is fully closed and continue holding the switch up for approximately 5 seconds after the window is completely closed.
  3. Command the window to express UP and express DOWN by pressing the window switch past the first detent and releasing and then pulling the window switch past the first detent and releasing. The window should perform the express UP and express DOWN functions.
  4. If the M74D window motor--driver does not perform as specified and the DTC resets, verify the vehicle doors are closed and repeat the normalisation procedure.

Repair Instructions

Perform the Diagnostic Repair Verification Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Front Side Door Window Regulator Replacement
    • Control Module References for BCM replacement, programming and setup
   


© Copyright Chevrolet. All rights reserved