To the top of the document
Orlando
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC P02CC-P02D3 — LNP or LNQ

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P02CC: Cylinder 1 Injector Exceeded Minimum Learning Limit

DTC P02CD: Cylinder 1 Injector Exceeded Maximum Learning Limit

DTC P02CE: Cylinder 2 Injector Exceeded Minimum Learning Limit

DTC P02CF: Cylinder 2 Injector Exceeded Maximum Learning Limit

DTC P02D0: Cylinder 3 Injector Exceeded Minimum Learning Limit

DTC P02D1: Cylinder 3 Injector Exceeded Maximum Learning Limit

DTC P02D2: Cylinder 4 Injector Exceeded Minimum Learning Limit

DTC P02D3: Cylinder 4 Injector Exceeded Maximum Learning Limit

Circuit/System Description

The engine control module (ECM) supplies voltage to each fuel injector on the injector positive voltage control circuits. The ECM energises each fuel injector by grounding the control circuit of that fuel injector. The ECM monitors the status of the injector positive voltage control circuits and the fuel injector control circuits. The injectors are separated into the following two groups:

    • Group 1 - Injectors 1 and 4
    • Group 2 - Injectors 2 and 3

When a fuel injector circuit condition is detected by the ECM, the affected fuel injector will be disabled and may disable the affected group of fuel injectors.

Conditions for Running the DTC
    • The engine is running.
    • The ECM monitors for a condition once per camshaft revolution.

Conditions for Setting the DTC

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match.

Action Taken When the DTC Sets

DTC P02CC, P02CD, P02CE, P02CF, P02D0, P02D1, P02D2 and P02D3 are Type B DTCs.

Conditions for Clearing the DTC

DTC P02CC, P02CD, P02CE, P02CF, P02D0, P02D1, P02D2 and P02D3 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification
  1. Ignition ON, observe the DTC information with a scan tool. DTCs P2147, P2148, P2150, P2151, P2153, P2154, P2156 or P2157 should not set.
    2. ⇒If any DTCs are set, refer to DTC P2147, P2148, P2150, or P2151 : LNP or LNQ .
  2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the affected fuel injector.
  2. Ignition ON, test for 2-3 V between the low control circuit terminal 2 and ground.
    3. ⇒If less than the specified range, test the low control circuit for an open/high resistance or for a short to ground. If the circuit tests normal, replace the K20 Engine Control Module.
    ⇒If greater than the specified range, test the low control circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module.
  3. Ignition ON, connect a test lamp between the affected fuel injector low control circuit terminal 1 and ground.
  4. Engine cranking or running, the test lamp should illuminate or flash.
    5. ⇒If the test lamp does not illuminate or flash, replace the K20 Engine Control Module.
  5. If all circuits test normal, test or replace the affected fuel injector.

Component Testing

Static Test

  1. Disconnect the harness connector at the affected fuel injector.

    2. Note: The DMM and test leads must be calibrated to 0 Ω in order to prevent misdiagnosis.

  2. Test for 0.2-1.5 Ω between the low control terminal 2 and the high control terminal 1.
    3. ⇒If not within the specified range, replace the fuel injector.
  3. Test for infinite resistance between each terminal and ground.
    4. ⇒If not the specified value, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Injector Replacement
    • Control Module References for ECM replacement, programming and setup
   


© Copyright Chevrolet. All rights reserved