Service Manual2007 Captiva Diagnostic Trouble Code (DTC) P0973

Captiva

Diagnostic Trouble Code (DTC) P0973

Shift Solenoid (SS) 1 Control Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 1 feedback circuit indicates a short to ground for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 1 and TCM
SS1
TCM

DTC P0973 - Shift Solenoid (SS) 1 Control Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0973 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid(SS) 1. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 16 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS1. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS1 connector terminal 14 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS1. Inspect the SS1. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS1.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0974

Shift Solenoid (SS) 1 Control Circuit High Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 1 feedback circuit indicates a continuous open or short to voltage for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.
TCM requests the ECM to limit engine torque to 185 N•m (136 lb-ft).

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 1 and TCM
SS1
TCM

DTC P0974 - Shift Solenoid (SS) 1 Control Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0974 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid(SS) 1. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 16 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS1. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS1 connector terminal 14 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS1. Inspect the SS1. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS1.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0976

Shift Solenoid (SS) 2 Control Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 2 feedback circuit indicates a short to ground for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 2 and TCM
SS2
TCM

DTC P0976 - Shift Solenoid (SS) 2 Control Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0976 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS) 2. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 15 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS2. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS2 connector terminal 7 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS2. Inspect the SS2. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS2.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0977

Shift Solenoid (SS) 2 Control Circuit High Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 2 feedback circuit indicates a continuous open or short to voltage for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear (short to voltage : 5th gear) when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 2 and TCM
SS2
TCM

DTC P0977 - Shift Solenoid (SS) 2 Control Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0977 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS) 2. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 15 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS2. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS2 connector terminal 7 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS2. Inspect the SS2. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS2.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0979

Shift Solenoid (SS) 3 Control Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 3 feedback circuit indicates a short to ground for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D, M+, M-, 2th gear range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 3 and TCM
SS3
TCM

DTC P0979 - Shift Solenoid (SS) 3 Control Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0979 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)3. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 14 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS3. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS3 connector terminal 13 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS3. Inspect the SS3. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS3.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0980

Shift Solenoid (SS) 3 Control Circuit High Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 3 feedback circuit indicates a continuous open or short to voltage for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 3th gear (short to voltage) or 4th gear (open) when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear (short to voltage) or 4th gear (open) when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 3 and TCM
SS3
TCM

DTC P0980 - Shift Solenoid (SS) 3 Control Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0980 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)3. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 14 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS3. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS3 connector terminal 13 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS3. Inspect the SS3. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS3.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0982

Shift Solenoid (SS) 4 Control Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 4 feedback circuit indicates a short to ground for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 4 and TCM
SS4
TCM

DTC P0982 - Shift Solenoid (SS) 4 Control Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0982 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)4. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 13 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS4. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS4 connector terminal 6 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS4. Inspect the SS4. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS4.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0983

Shift Solenoid (SS) 4 Control Circuit High Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 4 feedback circuit indicates a continuous open or short to voltage for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear (open) or 3th gear (short to voltage) when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 4 and TCM
SS4
TCM

DTC P0983 - Shift Solenoid (SS) 4 Control Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle.Is the Malfunction Indicator Lamp (MIL) ON? Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0983 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)4. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 13 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS4. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS4 connector terminal 6 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS4. Inspect the SS4. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS4.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0985

Shift Solenoid (SS) 5 Control Circuit Low Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 5 feedback circuit indicates a short to ground for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM requests the ECM to limit engine torque to 150 N•m (111 lb-ft).
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 5 and TCM
SS5
TCM

DTC P0985 - Shift Solenoid (SS) 5 Control Circuit Low Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle.Is the Malfunction Indicator Lamp (MIL) ON? Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0985 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)5. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 22 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS5. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS5 connector terminal 12 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS5. Inspect the SS5. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS5.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.

Diagnostic Trouble Code (DTC) P0986

Shift Solenoid (SS) 5 Control Circuit High Voltage

Conditions for Running the DTC

Emergency mode is OFF.
The elapsed time is 0.025 seconds after solenoid output changed.

Conditions for Setting the DTC

Shift solenoid (SS) 5 feedback circuit indicates a continuous open or short to voltage for 0.5 seconds.

Action Taken When the DTC Sets

TCM will request the illumination of MIL.
TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.
TCM stores DTC in TCM history.
TCM requests the ECM to limit engine torque to 150 N•m (111 lb-ft).
TCM turns Emergency mode ON.

When the Emergency mode is ON, the following conditions occur :

The transmission will operate in 4th gear when the transmission is shifted into D or M+ range.

The transmission will operate in 2th gear when the transmission is shifted into 2 or M- range.

Learn control is disabled.

Lock up control is disabled.

Adaptive control is disabled.

N-D shifting is disabled.

ABS function is disabled.

Conditions for Clearing the MIL/DTC

The MIL turns OFF when no failure is detected for three consecutive driving cycles.
The scan tool can clear the DTC from the TCM history.
TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

Cause of Failure

Wiring harness or connector between Shift Solenoid (SS) 5 and TCM
SS5
TCM

DTC P0986 - Shift Solenoid (SS) 5 Control Circuit High Voltage

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle.Is the Malfunction Indicator Lamp (MIL) ON? Is the Malfunction Indicator Lamp (MIL) ON?	-	Go to Step 2	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P0986 displayed?	-	Go to Step 3	Repair the temporary connection failure of connector (Refer to "Wiring Harness and Connector Inspection" in this section.)
3	Turn the ignition OFF. Inspect the resistance between the vehicle harness and Shift Solenoid (SS)5. Refer to "Unit Inspection" in this section. Disconnect the TCM connector J1 (X-1) and inspect the resistance between the terminal 22 and 23. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 4	Go to Step 5
4	Estimate the failure of between the vehicle wiring harness connector and TCM. Inspect the connector. Refer to "Wiring Harness and Connector Inspection" in this section. Inspect the connection condition between the connectors (C-1). Is the connection condition OK?	-	Go to Step 6	Repair the wiring harness connectors.
5	Estimate the failure of between the vehicle harness and SS5. Disconnect the connector (X-3) of T/M wire and inspect the resistance between SS5 connector terminal 12 and ground. Is the measurement within the specified value?	20°C (68°F) : 11-16Ω	Go to Step 7	Go to Step 8
6	Replace the master TCM. Perform the reproducing test under user condition after confirming no DTC. Is DTC displayed?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the TCM.
7	Estimate the failure of the vehicle wiring harness or between connectors. Inspect continuity and short circuit for the vehicle wiring harness and inspect the connection condition between connectors (C-3). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the vehicle harness or adjustment between connectors.
8	Estimate the failure of T/M wire or between connectors of SS5. Inspect the SS5. Refer to "Unit Inspection" in this section. Is the problem found?	-	Replace the SS5.	Go to Step 9
9	Estimate the failure of T/M wire. Inspect continuity and short circuit for the T/M wire and inspect the connection condition between connectors (C-5). Refer to "Wiring Harness and Connector Inspection" in this section. Is the condition OK?	-	Repair the temporary connection failure of connector. (Refer to "Wiring Harness and Connector Inspection" in this section.)	Replace the T/M wire or adjustment between connectors.