To the top of the document
Aveo
To Previous Page To Next Page
GMDE Start Page Load static TOC Load dynamic TOC Help?

SECTION 9G

INTERIOR TRIM

Caution : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.

SPECIFICATIONS

Fastener Tightening Specifications

Application
N•m
Lb-Ft
Lb-In
Door Pull Screw
3.5
-
31
Floor Console Screws
4
-
35
Gearshift Housing Bolts
5
-
44
Rear Seat Belt Anchor Bolts
38
28
-
Rear Seatback Bolt
25
18
-
Rear Seat Locking Pin
38
28
-
Seat Belt Anchor Bolts
38
28
-
Seat Belt Bracket Screws
10
-
89
Trim Panel Screws
3.5
-
31

SPECIAL TOOLS

Special Tools Table


KM475B
Display graphicTranslations of text in graphics
KM-475-B
Trim Remover

MAINTENANCE AND REPAIR

ON-VEHICLE SERVICE


S6B19P12
Display graphicTranslations of text in graphics


Front Door Trim

Tools Required

KM-475-B Trim Remover

Removal Procedure

  1. Lower the front window.
  2. Remove the front door handle cover and the screws.
  3. Remove the inside door handle escutcheon.

    4. S6B19G01
    Display graphicTranslations of text in graphics


  4. Pry off the trim using the trim remover KM-475-B.

S6B19G02
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the trim.
  2. Install the front door handle cover.

    3. Tighten
    Tighten the trim screws to 3.5 N•m (31 lb-in).

  3. Install the front door handle cover.
  4. Install the inside door handle escutcheon.

    5. S6B19P12
    Display graphicTranslations of text in graphics


  5. Raise the window.

S6B19P12
Display graphicTranslations of text in graphics


Rear Door Trim

Tools Required

KM-475-B Trim Remover

Removal Procedure

  1. Lower the rear window.
  2. Remove the rear door handle cover.
  3. Remove the door pull screws.
  4. Remove the inside door handle escutcheon.

    5. S6B19G03
    Display graphicTranslations of text in graphics


  5. Pry off the trim using the trim remover KM-475-B.

S6B19P12
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the trim.
  2. Install the rear door handle cover.

    3. Tighten
    Tighten the trim screws to 3.5 N•m (31 lb-in).

  3. Install the rear door handle cover.

    4. S6B19G04
    Display graphicTranslations of text in graphics


  4. Install the inside door handle escutcheon.
  5. Raise the window.

T3B19G06
Display graphicTranslations of text in graphics


Upper B-Pillar Trim

Removal Procedure

  1. Remove the bolt and the upper front seat belt anchor.
  2. Remove the lower B-pillar trim. Refer to "Lower B-Pillar Trim" in this section.
  3. Pry off the upper B-Pillar trim.

T3B19G06
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the upper B-pillar trim.
  2. Install the lower B-pillar trim. Refer to "Lower B-Pillar Trim" in this section.
  3. Install the upper front seat belt anchor with the bolt.

    4. Tighten
    Tighten the seat belt anchor bolt to 38 N•m (28 lb-ft).


S6B19G05
Display graphicTranslations of text in graphics


Lower B-Pillar Trim

Removal Procedure

  1. Reposition the rear portion of the front rocker panel cover and the front portion of the rear rocker panel cover.
  2. Remove the bolt and seat belt.
  3. Pry off the lower B-pillar trim.

S6B19G05
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the lower B-pillar trim.
  2. Install the front seat belt with the bolt.

    3. Tighten
    Tighten the seat belt bolt to 38 N•m (28 lb-in).

  3. Install the front rocker panel cover.
  4. Install the rear rocker panel cover to its original position.

S6B19G06
Display graphicTranslations of text in graphics


Upper Back Panel Shelf

Removal Procedure

  1. Remove the rear seatback. Refer to Section 9H, Seats.
  2. Remove the plastic retaining clips and the deck lid sill plate cover.

S6B19G06
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear deck lid sill plate cover with the plastic retaining clips.
  2. Install the rear seatback. Refer to Section 9H, Seats.

T3B19G11
Display graphicTranslations of text in graphics


Rear Door Interior Garnish Molding

Removal Procedure

  1. Pry off the rear door interior garnish molding.

T3B19G11
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear door interior garnish molding.

T3B19G12
Display graphicTranslations of text in graphics


Hatchback Door Lower Garnish Molding

Tools Required

KM-475-B Trim Remover

Removal Procedure

  1. Open the hatchback door.
  2. Remove the lower garnish molding clips using the trim remover KM-475-B.
  3. Remove the lower garnish molding.

T3B19G12
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the lower garnish molding with the clips.
  2. Close the hatchback door.

S6B19G07
Display graphicTranslations of text in graphics


Front Rocker Panel Cover

Removal Procedure

  1. Remove the screw securing the front rocker panel cover.
  2. Pry off the front rocker panel cover.

S6B19G07
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the front rocker panel cover with the screw.

S6B19G08
Display graphicTranslations of text in graphics


Rear Rocker Panel Cover

Removal Procedure

  1. Remove the rear seat cushion and rear seatback. Refer to Section 9H, Seats.
  2. Remove the clip securing the rear rocker panel cover.
  3. Remove the screw securing the front wheel house trim.
  4. Pry off the rear rocker panel cover.

S6B19G08
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear rocker panel cover.
  2. Install the front wheel house trim with the screw.
  3. Install the rear rocker panel cover with the clips.
  4. Install the rear seatback with the bolt.

    5. Tighten
    Tighten the rear seatback bolt to 25 N•m (18 lb-ft).

  5. Install the rear seat cushion. Refer to Section 9H, Seats.

S6B19G07
Display graphicTranslations of text in graphics


Floor Carpet

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the left and the right rear rocker panel cover. Refer to "Rear Rocker Panel Cover" in this section.
  3. Remove the bolts and the left and the right lower front seat belt anchors from the B-pillar.
  4. Remove the left and the right lower B-pillar trims. Refer to "Lower B-Pillar Trim" in this section.

    5. S6B19G09
    Display graphicTranslations of text in graphics


  5. Remove the front seats. Refer to Section 9H, Seats.
  6. Pry off the left and the right front rocker trim.
  7. Remove the floor console. Refer to "Floor Console" in this section.
  8. Remove the floor carpet.

S6B19G05
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the floor carpet.
  2. Install the floor console. Refer to "Floor Console" in this section
  3. Install the left and the right front rocker panel covers.
  4. Install the front seats. Refer to Section 9H, Seats.
  5. Install the left and the right lower B-pillar trim. Refer to "Lower B-Pillar Trim" in this section
  6. Install the left and the right lower front seat belt anchors to the B-pillar with the bolts.

    7. Tighten
    Tighten the seat belt anchor bolts to 38 N•m (28 lb-ft).

  7. Install the rear seatback. Refer to Section 9H, Seats.
  8. Install the left and the right rear rocker trim panels. Refer to "Rear Rocker Trim Panel" in this section
  9. Connect the negative battery cable.

S6B19G10
Display graphicTranslations of text in graphics


Floor Console

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever boot.

    3. S6B19G11
    Display graphicTranslations of text in graphics


  3. Remove the screws from the floor console.
  4. Remove the floor console cover.
  5. Remove the parking brake cover.
  6. Disconnect the electrical connector.
  7. Remove the floor console.

S6B19G11
Display graphicTranslations of text in graphics


Installation Procedure

  1. Connect the electrical connector.
  2. Install the floor console with the screws.

    3. Tighten
    Tighten the floor console screws to 4 N•m (35 lb-in).


    S6B19G12
    Display graphicTranslations of text in graphics


  3. Install the parking brake cover.
  4. Install the gearshift lever boot.
  5. Install the console cover.
  6. Connect the negative battery cable.

T3B19G23
Display graphicTranslations of text in graphics


A-Pillar Trim

Removal Procedure

  1. Pry off the A-pillar trim.
  2. Disconnect the electrical connector.

T3B19G23
Display graphicTranslations of text in graphics


Installation Procedure

  1. Connect the electrical connector.
  2. Install the A-pillar trim.

S6B19G13
Display graphicTranslations of text in graphics


C-Pillar Trim

Removal Procedure

  1. Remove the C-pillar trim.

S6B19G13
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the C-pillar trim panel.

T3B19G25
Display graphicTranslations of text in graphics


C-Pillar Trim - Hatchback -

Removal Procedure

  1. Remove the seat belt from the C-pillar trim.
  2. Remove the rear rocker panel cover. Refer to "Rear Rocker Panel Cover" in this section.
  3. Remove the C-pillar trim.

T3B19G25
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the C-pillar trim.
  2. Install the rear rocker panel cover. Refer to "Rear Rocker Panel Cover" in this section.
  3. Install the seat belt from the C-pillar trim.

T5B19G01
Display graphicTranslations of text in graphics


Front Side Panel Trim - Three Door Hatchback -

Removal Procedure

  1. Remove the rocker panel cover. Refer to "Rocker Panel Cover" in this section.
  2. Remove the rear seat. Refer to Section 9H, Seats.
  3. Remove the clips, seat belt lower anchor bolt and rear seat locking pin.
  4. Remove the front side panel trim.

T5B19G01
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the front side panel trim.
  2. Install the clips, seat belt lower anchor bolt and rear seat locking pin.

    3. Tighten

  3. Install the rear seat. Refer to Section 9H, Seats.
  4. Install the rocker panel cover. Refer to "Rocker Panel Cover" in this section.

T5B19G02
Display graphicTranslations of text in graphics


Load Compartment Side Cover

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the front side panel trim. Refer to "Front Side Panel Trim" in this section.
  3. Remove the clip from the rear side panel trim.
  4. Disconnect the speaker connector in load compartment side cover.
  5. Remove the screws from the load compartment side cover.
  6. Remove the load compartment side cover.

T5B19G02
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the load compartment side cover.
  2. Install the screws on the load compartment side cover.
  3. Connect the speaker connector in load compartment side cover.
  4. Install the clip on the rear side panel trim.
  5. Install the front side panel trim. Refer to "Front Side Panel Trim" in this section.
  6. Connect the negative battery cable.

T5B19L02
Display graphicTranslations of text in graphics


Quarter Window Trim - Three Door Hatchback -

Removal Procedure

  1. Remove the front side panel trim. Refer to "Front Side Panel Trim" in this section.
  2. Remove the seat belt upper anchor bolt.
  3. Remove the load compartment side cover. Refer to "Load Compartment Side Cover" in this section.
  4. Remove the quarter window trim.

T5B19L02
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the quarter window trim
  2. Install the load compartment side cover. Refer to "Load Compartment Side Cover" in this section.
  3. Install the seat belt upper anchor bolt.

    4. Tighten
    Tighten the seat belt upper anchor bolt to 38 N•m (28 lb-ft).

  4. Install the front side panel trim. Refer to "Front Side Panel Trim (Three Door Hatchback)" in this section.

T3B19G26
Display graphicTranslations of text in graphics


Front Door Escutcheon

Removal Procedure

  1. Pry off the escutcheon.

T3B19G26
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the escutcheon.

S6B19G14
Display graphicTranslations of text in graphics


Rear Side Panel Trim

Removal Procedure

  1. Remove the Lower Back Panel cover. Refer to Lower Back Panel Cover in this section
  2. Remove the clips and the rear side panel trim.

S6B19G14
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the rear side panel trim with the clips.
  2. Install the Lower Back Panel Cover. Refer to Lower Back Panel Cover in this section.
  3. Install the rear seatback. Refer to Section 9H, Seats.

T3B19G28
Display graphicTranslations of text in graphics


Rear Side Panel Trim - Hatchback -

Removal Procedure

  1. Remove the clips and the rear side panel trim.

T3B19G28
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the clips and the rear side panel trim.

S6B19G17
Display graphicTranslations of text in graphics


Rear Wheel House Trim

Removal Procedure

  1. Remove the rear seatback. Refer to Section 9H, Seats.
  2. Remove the rear rocker panel cover.
  3. Remove the front wheel house trim.

    4. S6B19G15
    Display graphicTranslations of text in graphics


  4. Remove the wheel house brack trim.
  5. Remove the plastic retaining clips and the rear side panel trim.

S6B19G15
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the rear side panel trim with the plastic retaining clips.
  2. Install the front wheel house trim.

    3. S6B19G17
    Display graphicTranslations of text in graphics


  3. Install the front wheel house trim.
  4. Install the rear rocker panel trim.
  5. Install the rear rocker seatback. Refer to Section 9H, Seats.

S6B19G16
Display graphicTranslations of text in graphics


Lower Back Panel Cover

Removal Procedure

  1. Remove the plastic retaining clips and the back panel lower cover.

S6B19G16
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the back panel lower cover with the plastic retaining clips.

GENERAL DESCRIPTION AND SYSTEM OPERATION

Interior Trim Panels

The interior trim panels are molded plastic and fasten with screws or plastic clips.

Pressure Relief Vent

When all the windows are closed and the ventilation system is on, the addition of outside air to the interior of the vehicle causes a positive pressure within the vehicle. In order to relieve the pressure, air is released through two pressure relief vents. The pressure relief vents are located at the rear quarter of the vehicle, behind the bumper fascia.

Floor Console

The floor console fits over the tunnel in the floor of the vehicle and extends from under the center of the instrument panel to the rear seat area. The front portion of the console contains the cigar lighter and the transaxle shift lever. The rear portion of the console contains the parking brake lever, the power window switches, (if equipped), and a cupholder.
The sensing and diagnostic module (SDM) for the airbag system is located under the front part of the console.

Floor Carpet

The molded one-piece floor carpet goes over both the front and the rear floor pans.


To Previous Page To Next Page
© Copyright Chevrolet Europe. All rights reserved