Service Information

Cruze

3-5-Reverse and 4-5-6 Clutch Housing Disassemble - 6T40/45/50 - Gen 1

Table 1:	Turbine Shaft, Reluctor Wheel and Piston Removal
Table 2:	4-5-6 Clutch Plate Removal
Table 3:	4-5-6 Clutch Piston Removal
Table 4:	Reluctor Wheel and Piston Removal
Table 5:	3-5 Reverse Clutch Plate Removal

Callout	Component Name
1	Turbine Shaft Retainer Ring Tip Discard the retainer ring. It is not re-usable. Special Tools GE 5586-A Circlip Pliers or equivalent For equivalent regional tools, refer to Special Tools .
2	Turbine Shaft
3	Reaction Carrier Hub Assembly
4	Reaction Carrier Hub Thrust Bearing Assembly

Callout	Component Name
1	4-5-6 Clutch Backing Plate Retaining Ring
2	4-5-6 Clutch Backing Plate
3	4-5-6 Clutch Plate Assembly (Qty: 4)
4	4-5-6 Clutch Plate (Qty: 3)
5	4-5-6 Clutch Apply Plate
6	4-5-6 Clutch Wave Plate

Callout

Component Name

4-5-6 Clutch Dam Retaining Ring

Tip
The 4-5-6 clutch dam retaining ring is not reusable.

•	DT-47951-2 Spring Compressor

•	GE 5586-A Circlip Pliers or equivalent

For equivalent regional tools, refer to Special Tools .

4-5-6 Clutch Piston Fluid Dam Assembly

Place the 3-5 reverse and 4-5-6 clutch housing onto the support hub in the case.
Apply shop air to the 4-5-6 clutch feed hole using a rubber tipped air gun to dislodge the dam piston and the 4-5-6 clutch piston from the clutch housing.

4-5-6 Clutch Piston Return Spring Assembly

4-5-6 Clutch Piston

Tip
Apply shop air to the 4-5-6 clutch feed hole using a rubber tipped air gun to dislodge the clutch piston.

4-5-6 Clutch Piston Inner Seal

4-5-6 Clutch Piston Outer Seal (Dark Blue) (Stepped)

4-5-6 Clutch Piston Outer Seal (Large) (Rounded)

Callout	Component Name
1	Input Shaft Speed Sensor Reluctor Ring Retainer Ring Caution: Compress the reluctor wheel just enough to clear the retainer. Over compressing the reluctor wheel will break the alignment tab and the clutch housing. Special Tool DT-47694 Piston Spring Compressor For equivalent regional tools, refer to Special Tools .
2	Input Shaft Speed Sensor Reluctor Wheel
3	3-5 Reverse Clutch Piston
4	3-5 Reverse Clutch Piston Return Spring Assembly
5	3-5 Reverse Clutch Piston Inner (Reluctor) Seal (Orange)
6	3-5 Reverse Clutch Piston Inner Seal
7	3-5 Reverse Clutch Piston Dam Seal (Black)

Callout	Component Name
1	3-5 Reverse Clutch Backing Plate Ring Retainer Ring Tip Gently push down on the backing plate to get enough clearance between the backing plate and retainer.
2	3-5 Reverse Clutch Backing Plate
3	3-5 Reverse Clutch Plate Assembly (Qty: 3)
4	3-5 Reverse Clutch Plate (Qty: 3)
5	3-5 Reverse Clutch Apply Plate (Waved)