To the top of the document
Cruze
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Fuel Injector Diagnosis - Scan Tool

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Circuit/System Description

The control module enables the appropriate fuel injector pulse for each cylinder. The ignition voltage is supplied directly to the fuel injectors. The control module controls each fuel injector by grounding the control circuit via a solid state device called a driver. A fuel injector coil winding resistance that is too high or too low will affect the engine driveability. A fuel injector control circuit DTC may not set, but a misfire may be apparent. The fuel injector coil windings are affected by temperature. The resistance of the fuel injector coil windings will increase as the temperature of the fuel injector increases.

When performing the fuel injector balance test, the scan tool is first used to energise the fuel pump relay. The fuel injector tester or the scan tool is then used to pulse each injector for a precise amount of time, allowing a measured amount of the fuel to be injected. This causes a drop in the system fuel pressure that can be recorded and used to compare each injector.

Diagnostic Aids
    • Monitoring the misfire current counters, or misfire graph, may help to isolate the fuel injector that is causing the condition.
    • Operating the vehicle over a wide temperature range may help isolate the fuel injector that is causing the condition.
    • Perform the fuel injector coil test within the conditions of the customers concern. A fuel injector condition may only be apparent at a certain temperature, or under certain conditions.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Special Tools

CH 48027 Digital Pressure Gauge

For equivalent regional tools, refer to Special Tools .

Component Testing

Fuel Injector Coil Static Test

Verify the resistance of each fuel injector with one of the following methods:

    • If the B34A Engine Coolant Temperature Sensor 1 is between 10-32°C (50-90°F), the resistance of each fuel injector should be 11-14 Ω.
       ⇒If the injectors measure OK, perform the fuel injector balance test/fuel pressure test.
       ⇒If not within the specified range, replace the fuel injector.
    • If the B34A Engine Coolant Temperature Sensor 1 is not between 10-32°C (50-90°F), measure and record the resistance of each fuel injector with a DMM. Subtract the lowest resistance value from the highest resistance value. The result obtained should be equal to or less than 3 Ω.
       ⇒ the difference is equal to or less than 3 Ω, perform the fuel injector balance test/fuel pressure test.
       ⇒If the difference is more than 3 Ω, add up all of the fuel injector resistance values to obtain a total resistance value. Divide the total resistance value by the number of fuel injectors to obtain an average resistance value. Subtract the lowest individual fuel injector resistance value from the average resistance value. Compute the difference between the highest individual fuel injector resistance value and the average resistance value. Replace the fuel injector that displays the greatest difference above or below the average.

Fuel Injector Balance Test-Fuel Pressure Static Test

    Note: 

       • Do not perform this test if the engine coolant temperature (ECT) is above 94°C (201°F). Irregular fuel pressure readings may result due to hot soak fuel boiling.
       • Verify that an adequate amount of fuel is in the fuel tank before proceeding with this diagnostic.
       • Before proceeding with this test review the user manual of the CH 48027 digital pressure gauge for Safety Information and Instructions.

  1. Install a fuel pressure gauge. Refer to Fuel Pressure Gauge Installation and Removal : 1.6L LDE, LXV, and 1.8L 2H0 .
  2. Turn ON the ignition, with the engine OFF.

    3. Note: 

       • The fuel pump relay may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
       • Do not start the engine.

  3. Command the fuel pump relay ON with a scan tool.
  4. Observe the fuel pressure gauge with the fuel pump commanded ON. The fuel pressure should be 345-414 kPa (50-60 PSI).
    5. ⇒If the fuel pressure is not 345-414 kPa (50-60 PSI), refer to Fuel System Diagnosis .
  5. Monitor the fuel pressure gauge for 1 min. The fuel pressure should not decrease more than 34 kPa (5 PSI).
    6. ⇒If the fuel pressure decreases more than 34 kPa (5 PSI), refer to Fuel System Diagnosis .
  6. Perform the Fuel Injector Balance Test with scan tool.

Fuel Injector Balance Test with Scan Tool Static Test

  1. Command the fuel pump relay ON and then OFF three times with a scan tool. On the last command, as the fuel pressure begins to slowly degrade and stabilise, select a fuel pressure within 34 kPa (5 PSI) of the maximum pump pressure. Record this fuel pressure. This is the starting pressure at which you will pulse each injector.
  2. With a scan tool, select the fuel injector balance test function within the special functions menu.
  3. Select an injector to be tested.
  4. Press Enter to prime the fuel system.
  5. Energise the fuel injector by depressing the pulse injector button on the scan tool at the previously selected pressure.
  6. After the injector stops pulsing, select Min from the display mode on the CH 48027 digital pressure gauge and record the Min pressure.

    7. Note: New test results will not be recorded if the Min/Max results are not cleared after each injector is tested.

  7. Clear the Min/Max results on the CH 48027 digital pressure gauge .
  8. Select normal from the display mode on the CH 48027 digital pressure gauge .
  9. Press enter on the scan tool to bring you back to the select injector screen.
  10. Repeat steps 3 through 9 for each fuel injector.
  11. Perform the pressure drop calculation.

Pressure Drop Calculation Static Test

  1. Subtract the minimum pressure from the starting pressure for one fuel injector. The result is the pressure drop value.
  2. Obtain a pressure drop value for each fuel injector.
  3. Add all of the individual pressure drop values except for the injector suspected of being faulty. This is the total pressure drop.
  4. Divide the total pressure drop by the number of fuel injectors that were added up. This is the average pressure drop. The difference between any individual pressure drop and the average pressure drop should not be more than 20 kPa (3 PSI).
    5. ⇒If the difference between any individual pressure drop and the average pressure drop is more than 20 kPa (3 PSI), replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Fuel Injector Replacement : 1.6L LDE, LXV, 1.8L 2H0, and LUW

   


© Copyright Chevrolet. All rights reserved