Cruze

Piston, Connecting Rod, and Bearing Cleaning and Inspection - 1.4L LUH and LUJ

Special Tools

EN-470-B Angular Torque Wrench

For equivalent regional tools, refer to Special Tools .

Connecting Rod

Warning: Wear safety glasses when using compressed air in order to prevent eye injury.

1. Clean the connecting rods in solvent and dry with compressed air
2. Inspect the connecting rod for the following:

•	Signs of being twisted, bent, nicked or cracked

•	Scratches or abrasion on the connecting rod bearing seating surfaces

Piston

1. Clean the piston with a cleaning solvent. DO NOT wire brush any parts of the piston.
2. Clean the piston ring grooves.
3. Inspect the piston on the following:

•	Cracked ring lands, skirts or pin bosses

•	Ring grooves for nicks

•	Eroded areas on the top of the piston (1)

•	Scuffed or damaged skirts (2)

•	Worn gudgeon pin bores (3)

4. If there is any excessive wear, replace the piston
5. Measure the clearance between piston pin and piston bore.

Piston Ring Clearance

1. Install the piston rings to the cylinder as shown (1) and measure the piston ring end gap. Compare the measurements with those provided below:

•	The upper compression ring end gap should be 0.4 mm - 0.6 mm (0.0157 in - 0.0236 in).

•	The lower compression ring end gap should be 0.4 mm - 0.6 mm (0.0157 in - 0.0236 in).

•	The oil ring end gap should be 0.2 mm - 0.9 mm (0.0079 in - 0.0354 in).

2. If the clearance is greater than the provided specifications, the piston rings must be replaced.



3. Measure the piston ring side clearance as shown (1). Compare the measurements with those provided below:

•	The upper compression ring side clearance should be 0.025 mm - 0.07 mm (0.001 in - 0.0028 in).

•	The lower compression ring side clearance should be 0.025 mm - 0.07 mm (0.001 in - 0.0028 in).

•	The oil ring side clearance should be 0.04 mm - 0.12 mm (0.0016 in - 0.0047 in).

4. If the clearance is greater than the provided specifications, replace the piston rings.
5. If the clearance is still to great, replace the pistons.

Connecting Rod Bearing Clearance (With Micrometer Gauge Internal Measuring Device)

1. Install the connecting bearings and the connecting rod bearing caps.
2. Tighten the connecting rod bearing cap bolts in the following sequence:

Caution: Refer to Fastener Caution in the Preface section.

Note: The old bolts can be reused for the measuring procedure.

2.1.	Tighten the connecting rod bearing cap bolts to 10 N·m (89 lb in).

2.2.	Tighten the bolts to an additional 60°. Use EN-470-B wrench .

2.3.	Tighten the bolts to an additional 15°. Use EN-470-B wrench .




3. Measure the connecting rod bearing diameters at 3 points as shown (1). Use an internal measuring device.
4. Calculate the average connecting rod inner diameter.

Formula: 1. result + 2. result + 3. result / 3




5. Measure the connecting rod journal diameter at 2 points between 1 and 3 and between 2 and 4. Use a micrometer gauge.
6. Calculate the average connecting rod journal diameter.

Formula: 1. result + 2. result / 2.

7. Subtract the average connecting rod journal diameter from the average connecting rod bearing diameter in order to determine the connecting rod bearing clearance.

The clearance should be 0.013 mm - 0.061 mm (0.0005 in - 0.0024 in).