Cruze

Valve Stem Oil Seal and Valve Spring Replacement

Special Tools

For equivalent regional tools, refer to Special Tools .

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the front compartment splash shield right hand side. Refer to Front Compartment Splash Shield Replacement .
3. Lower the vehicle.
4. Remove the hydraulic valve clearance adjuster arms. Refer to Hydraulic Valve Clearance Adjuster Arm Replacement .
5. Remove the spark plugs. Refer to Spark Plug Replacement .

Note: Wheels must be in contact with the ground.

6. Shift to 5. gear (MT) or park position (AT) and apply the park brake.
7. Adjust the engine to TDC of cylinder 1 and fix the crankshaft. Refer to Camshaft Timing Chain Adjustment .



8. Mark the crankshaft balancer 180° opposed to the cylinder 1 TDC marking.

1. Prepare the 2 EN-6086-6 supports (1) for the installation by tightening the support head in a centred position to the rail with the bolt (2).



2. Install the EN-6086-5 mounting shaft (3) along with the 2 EN-6086-6 supports (4) and the EN-6086-8 handle to the cylinder head.

Note: The demounting piece must point to the intake side.

3. Install the EN-6086-7 lever (2) along with the EN-6086-11 demounting piece (1) to the mounting shaft.
4. Position the mounting shaft centred above the spark plug bores and tighten the 4 fasteners (6).
5. Install the EN-6086-15 pneumatic adapter (5) to the spark plug screw bore of cylinder 1.
6. Apply air pressure to cylinder 1.



7. Remove the valve keys, valve spring retainers and the valve springs of the intake valves of cylinder 1, using the following procedure:

Caution: The demounting piece part of EN-6086 Basic Kit, Spring and Wedge Replacer must be applied parallel to the valve retainers in order to prevent damage to the tools or the valve train components. If demounting piece is not applied parallel it could cause damage to the valve stem keys or the valve retainers.

7.1.	Apply tension to the valve springs, using the EN-6086-7 lever (1) and the EN-6086-11 demounting piece (2) until the valve keys are discharged from spring load and remove the valve keys.

7.2.	Release tension from the valve springs and remove the valve spring retainers and the valve springs.




8. Remove the intake valve stem oil seals (2) of cylinder 1, using the EN-840 pliers (1).

Note: Lubricate the NEW intake valve stem oil seals with clean engine oil.

1. Install the NEW intake valve stem oil seals of cylinder 1, using the EN-958 installer (1).



2. Prepare the EN-6086-200-1 mounting piece for the valve key installation. The mounting piece must be assembled in the following order:

2.1.	Support (6)

2.2.	Bushing (5)

2.3.	Spring (4)

2.4.	EN-6086-200-10 plunger (3)

2.5.	Screw Connection (2)

2.6.	Lever Adapter (1)




3. Install the valve keys (1) to the mounting piece (2) and fix them with the bushing.



4. Install the intake valve springs, the intake valve spring retainers and the intake valve keys, using the following procedure:

4.1.	Replace the EN-6086-11 demounting piece with the assembled EN-6086-200-1 mounting piece (1).

4.2.	Install the intake valve springs and the intake valve spring retainers to the cylinder head.

Caution: The demounting piece part of EN-6086 Basic Kit, Spring and Wedge Replacer must be applied parallel to the valve retainers in order to prevent damage to the tools or the valve train components. If demounting piece is not applied parallel it could cause damage to the valve stem keys or the valve retainers.

Note: The cone side of the valve keys must point to the valve stem.

4.3.	Push down the mounting piece (1) using the lever (2) until the valve keys audibly engage.





4.4.	Inspect the intake valve keys (1) for proper seating.

Remove the exhaust valve stem oil seals of cylinder 1:

1. Transfer the EN-6086-7 lever to the exhaust side of cylinder 1.
2. Replace the EN-6086-200-1 mounting piece with the EN-6086-11 demounting piece .
3. Remove the exhaust valve keys, exhaust valve spring retainers, exhaust valve springs and the exhaust valve stem oil seals as described above.

1. Replace the EN-6086-11 demounting piece with the assembled EN-6086-200-1 mounting piece (1).
2. Install the exhaust valve keys, exhaust valve spring retainers, exhaust valve springs and the exhaust valve stem oil seals of cylinder 1 as described above.

1. Release the air pressure from cylinder 1.
2. Transfer the EN-6086-15 pneumatic adapter from cylinder 1 to the spark plug bore of cylinder 4.
3. Apply air pressure to cylinder 4.
4. Transfer the EN-6086-7 lever to the intake side of cylinder 4.
5. Replace the EN-6086-200-1 mounting piece with the EN-6086-11 demounting piece .
6. Remove the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 4 as described above.

1. Replace the EN-6086-11 demounting piece with the assembled EN-6086-200-1 mounting piece .
2. Install the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 4 as described above.

Replace the exhaust valve keys, exhaust valve spring retainers, exhaust valve springs and the exhaust valve stem oil seals of cylinder 4 as described above.

1. Release the air pressure from cylinder 4.
2. Raise the vehicle.
3. Remove the EN-952 fixing pin from the crankshaft.



4. Rotate the crankshaft balancer in engine rotation direction until the 180° opposite marking (2) aligns with the marking (1) on the engine front cover.
5. Lower the vehicle.

Note: Wheels must be in contact with the ground.

6. Block the engine by shifting the 5. gear (MT) or park position (AT) and applying the park brake.
7. Transfer the EN-6086-15 pneumatic adapter from cylinder 4 to the spark plug bore of cylinder 2.
8. Apply air pressure to cylinder 2.
9. Transfer the EN-6086-7 lever to the intake side of cylinder 2.
10. Replace the EN-6086-200-1 mounting piece with the EN-6086-11 demounting piece .
11. Remove the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 2 as described above.

1. Transfer the EN-6086-7 lever to the exhaust side of cylinder 2.
2. Replace the EN-6086-11 demounting piece with the assembled EN-6086-200-1 mounting piece (1).
3. Install the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 2 as described above.

Replace the exhaust valve keys, exhaust valve spring retainers, exhaust valve springs and the exhaust valve stem oil seals of cylinder 2 as described above.

1. Release the air pressure from cylinder 2.
2. Transfer the EN-6086-15 pneumatic adapter from cylinder 2 to the spark plug bore of cylinder 3.
3. Apply air pressure to cylinder 3.
4. Transfer the EN-6086-7 lever to the intake side of cylinder 3.
5. Replace the EN-6086-200-1 mounting piece with the EN-6086-11 demounting piece .
6. Remove the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 3 as described above.

1. Transfer the EN-6086-7 lever to the exhaust side of cylinder 3.
2. Replace the EN-6086-11 demounting piece with the assembled EN-6086-200-1 mounting piece .
3. Install the intake valve keys, intake valve spring retainers, intake valve springs and the intake valve stem oil seals of cylinder 3 as described above.

Replace the exhaust valve keys, exhaust valve spring retainers, exhaust valve springs and the exhaust valve stem oil seals of cylinder 3 as described above.

1. Release air pressure from cylinder 3.
2. Remove the EN-6086-15 pneumatic adapter.
3. Remove all parts of EN-6086 spring and wedge replacer .
4. Shift to neutral gear and release the park brake.
5. Adjust the engine to TDC of cylinder 1 and fix the crankshaft with EN-952 fixing pin .
6. Install the spark plugs. Refer to Spark Plug Replacement .
7. Install the hydraulic valve clearance adjuster arms. Refer to Hydraulic Valve Clearance Adjuster Arm Replacement .
8. Raise the vehicle.
9. Remove the EN-952 fixing pin and install the crankshaft bearing cap tie plate hole plug. Refer to Camshaft Timing Chain Adjustment .
10. Install the front compartment splash shield right side. Refer to Front Compartment Splash Shield Replacement .
11. Lower the vehicle.