Service Information

Cruze

DTC P1258

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P1258: Engine Coolant Overtemperature - Protection Mode Active

The engine control module (ECM) uses the engine coolant temperature sensor to monitor the engine for an over-temperature condition. This condition occurs when the coolant temperature is above a calibrated value. The ECM will alternately disable 2 groups of cylinders by turning OFF the fuel injectors. By switching between the 2 groups of cylinders, the ECM is able to reduce the temperature of the coolant.

Conditions for Running the DTC

•	DTCs P0116, P0117, P0118, P0128 are not set.

•	The engine is operating for greater than 30 s.

•	DTC P1258 runs continuously once the conditions above have been met.

Conditions for Setting the DTC

The ECM detects that engine coolant temperature is warmer than 136°C (277°F) for greater than 1 s.

Action Taken When the DTC Sets

•	DTC P1258 is a Type A DTC.

•	The engine will operate in the Overheated Engine Protection Operating Mode.

•	The Instrument Cluster will illuminate the coolant temperature indicator lamp and the driver information centre, if equipped, may display a message.

Conditions for Clearing the DTC

DTC P1258 is a Type A DTC.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

•	Cooling System Description and Operation : 2.0L Diesel LNP → 1.4L LDD and LUJ → 2.0L Diesel LLW

•	Instrument Cluster Description and Operation

•	Indicator/Warning Message Description and Operation

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Engine Control Module Scan Tool Information : LNP → LUJ → LXT → LXV, 2H0 → LLW for scan tool information

Circuit/System Verification

If DTC P0480, P0481, P0691, P0692, P0693, or P0694 is set, diagnose that DTC first.
Observe the engine coolant level. The engine coolant level should be within the operating range. Refer to Capacities, Approximate Fluid, and Engine Coolant in the Owner's Manual.
Ensure that the vehicle has the correct engine coolant with correct concentration and is not old, contaminated, or contains additives. Refer to Recommended Fluids and Lubricants in the Owner's Manual.
Inspect the cooling system for the following:

•

Leaks

•	Kinked or pinched hoses, especially at the radiator

•	Loose, missing, or damaged radiator air seals or deflectors

•	Air flow obstructions or bent fins at the radiator or the A/C condenser, Refer to Symptoms - Engine Cooling .

Note: A small delay occurs before the ECM changes the cooling fan speed.

Command the cooling fans ON and OFF, low and high speed. The engine cooling fans should turn ON and OFF with each command.

⇒	If the cooling fans do not function as indicated, refer to Cooling Fan Inoperative : LLW → LXV, 2H0 → LXT .

Circuit/System Testing

Test the thermostat for correct operation. Refer to Thermostat Diagnosis : 2.0L Diesel LNP → 2.0L Diesel LLW → LDE, L2W, LXT, LXV, 2H0, and LUW .
Test the engine cooling system for overheating. Refer to Engine Overheating .
Inspect the water pump and coolant flow for correct operation.
Inspect the engine mechanical for worn, leaking, cracked cylinder heads or engine block.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.