To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B0014

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using the diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0014 01: Driver Seat Side Air Bag Deployment Loop Short to Battery

DTC B0014 02: Driver Seat Side Air Bag Deployment Loop Short to Ground

DTC B0014 04: Driver Seat Side Air Bag Deployment Loop Open Circuit

DTC B0014 0D: Driver Seat Side Air Bag Deployment Loop Resistance Above Threshold

DTC B0014 0E: Driver Seat Side Air Bag Deployment Loop Resistance Below Threshold

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Driver Seat Side Air Bag High Circuit

B0014 02

B0014 0D

B0014 04

B0014 01

B0014 0E

Driver Seat Side Air Bag Low Circuit

B0014 02

B0014 0D

B0014 04

B0014 01

B0014 0E

Circuit/System Description

If a malfunction is detected, a DTC will be stored in non-volatile memory. During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the driver seat side air bag. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. A shorting bar is used within the driver seat side air bag connector which will short together both high and low circuits when the connector is disconnected. This will help to prevent unwanted deployment of the air bag during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 V.

Conditions for Setting the DTC

B0014 01

The driver seat side air bag high and/or low circuit is shorted to voltage.

B0014 02

The driver seat side air bag high and/or low circuit is shorted to ground.

B0014 04

The driver seat side air bag high and/or low circuit is open.

B0014 0D

The driver seat side air bag deployment loop resistance is more than 3.45 Ω.

B0014 0E

The driver seat side air bag deployment loop resistance is less than 1.77 Ω.

Action Taken When the DTC Sets

    • The SDM commands the AIR BAG indicator ON via serial data communications.
    • The SIR System is disabled and no deployments are allowed.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Testing

    Note: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.

       • Driver seat side air bag
       • SDM
       • Driver seat side air bag wiring harness connector
       • SDM wiring harness connector

  1. Ignition OFF, disconnect driver seat side air bag in-line connector.
  2. Disconnect the SDM connector.
  3. Test the high and low circuits between the SDM and driver seat side air bag for a short to voltage, short to ground, short between circuits or open/high resistance. Verify that a short to voltage, short to ground, short between circuits or open/high resistance does not exist.
  4. If any of the above conditions are found make the appropriate repair.
  5. If all circuits test normal then replace the SDM.
  6. Ignition ON, use a scan tool to observe the SIR DTC display. Verify DTC B0014 is set current.
  7. Replace the driver seat side air bag.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    • Driver Seat Side Air Bag
    • Control Module References for SDM replacement, setup, and programming
   


© Copyright Chevrolet. All rights reserved