To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B3933

Circuit Description

The HVAC control module monitors the evaporator temperature via the evaporator temperature sensor. When the air is cold, the sensor resistance and signal voltage are high. When the air is warm, the sensor resistance and signal voltage are low.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B3933 Evaporator Temperature Sensor Circuit

Conditions for Running the DTC

The ignition is turned ON.

Conditions for Setting the DTC

The HVAC control module detects the evaporator temperature sensor signal circuit is less than 0.09 volt (5 counts) or greater than 4.90 volts (250 counts).

Action Taken When the DTC Sets
    • The A/C OFF segment will illuminate on the HVAC control module.
    • The A/C compressor will be disabled.

Conditions for Clearing the DTC
    • The DTC will become history if the HVAC control module no longer detects a failure.
    • The history DTC will clear after 50 fault-free ignition cycles.
    • The DTC can be cleared with a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for correct operation of the circuit in the high voltage range.

    2.

  2. This step tests for correct operation of the circuit in the low voltage range. If the fuse in the jumper opens upon performing this test, the signal circuit has a short to voltage.

Step

Action

Values

Yes

No

Schematic Reference:HVAC Schematics

Connector End View Reference: Component Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

-

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Evaporator Temp parameter in the Climate Control Panel, Open/Short data list.

Does the scan tool indicate that the Evaporator temp parameter is within the specified range?

0.09-4.90 V

Go to Step 3

Go to Step 4

3

Check the connections at the Climate Control Panel and replace the terminals if necessary.

Is the repair complete?

 

Go to Diagnostic System Check - Vehicle

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the evaporator temperature sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Evaporator Temp parameter.

Is the Evaporator Temp parameter greater than the specified value?

4.90 V

Go to Step 5

Go to Step 6

5

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the signal circuit of the evaporator temperature sensor and the low reference circuit of the evaporator temperature sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Evaporator Temp parameter.

Is the Evaporator Temp parameter less than the specified value?

0.09 V

Go to Step 10

Go to Step 7

6

Test the signal circuit of the evaporator temperature sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 11

7

Test the signal circuit of the evaporator temperature sensor for one of the following conditions:

    • A short to voltage
    • A high resistance
    • An open

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 8

8

Test the low reference circuit of the evaporator temperature sensor for one of the following conditions:

    • A high resistance
    • An open

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 9

9

Test the following signal circuits for a short to voltage:

    • Inside air temperature sensor
    • Ambient air temperature sensor
    • Left sunload sensor
    • Right sunload sensor
    • Ambient light sensor

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 11

10

Inspect for poor connections at the harness connector of the evaporator temperature sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 12

11

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

-

Go to Step 14

Go to Step 13

12

Replace the evaporator temperature sensor. Refer to Air Conditioning Evaporator Core Replacement .

Did you complete the replacement?

-

Go to Step 14

-

13

Replace the HVAC control module. Refer to Air Conditioning and Heater Module Assembly Removal and Installation .

Did you complete the replacement?

-

Go to Step 14

-

14
  1. Use the scan tool to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC reset?

-

Go to Step 2

System OK

   


© Copyright Chevrolet. All rights reserved