To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC P2534

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P2534: Ignition On/Start Switch Circuit Low Voltage

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Ignition 1 voltage

P2534 open fuse

P2534

-

P0562, P0563

Circuit/System Description

The transmission control module (TCM) continuously monitors the system voltage on the Ignition 1 voltage circuit. Lower than normal voltage may be inadequate to operate the transmission control solenoids properly. Improper solenoid operation may cause erratic transmission operation, which may result in internal damage.

Conditions for Running the DTC

The engine control module (ECM) communicates that the engine is running through the controller area network (CAN).

Conditions for Setting the DTC

The TCM detects less than 6 volts on the ignition voltage circuit at the TCM for 7 seconds or greater.

Action Taken When the DTC Sets

    • DTC P2534 is a Type A DTC.
    • The TCM turns OFF the high side driver.
    • The TCM turns OFF all solenoids.
    • The TCM commands maximum line pressure.
    • the TCM freezes transmission adaptive functions.
    • The TCM commands the torque converter clutch (TCC) OFF.
    • The TCM limits the transmission to reverse and 5th gear.
    • The TCM inhibits Tap up/Tap down/MUMD operation.

Conditions for Clearing the DTC

DTC P2534 is a Type A DTC.

Diagnostic Aids

    • Observe the driver information centre (DIC) messaging that would indicate the electrical system requires service.
    • Inspect for the following conditions:
       - Loose or damaged terminals at the generator
       - Loose or worn generator drive belt

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

    •  Transmission General Description
    •  Transmission Component and System Description
    •  Electronic Component Description

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

DT-48616-10 Adapter Harness

Circuit/System Verification

  1. Engine ON, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6-15.0 volts.
  2. If not within the specified range, refer to Charging System Test .
  3. Observe the scan tool TCM Ignition Voltage parameter. The reading should be between 12.6-15.0 volts.
  4. After performing the above steps, verify that the DTC does not reset by operating the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions you observe from the Freeze Frame/Failure Records data. If the vehicle passes the Circuit/System Verification procedure, then STOP. Do not perform the Circuit/System Testing or Component Testing as this may result in an unnecessary part replacement. Refer to Testing for Intermittent Conditions and Poor Connections .

Circuit/System Testing

    Note: You must perform the Circuit/System Verification first.

  1. Ignition OFF, disconnect the 14-way harness connector at the transmission.
  2. Connect the DT-48616-10 harness to the 14-way transmission harness connector.
  3. Test for less than 10 ohms between the ground circuit terminal 2 and ground.
  4. If greater than the specified range, test the ground circuit for an open/high resistance.
  5. Ignition ON, verify that a test lamp illuminates between the B+ and ignition circuit terminals listed below and ground.
  6. • Terminal 1
    • Terminal 12
    • Terminal 13
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  7. If all circuits test normal, replace the control solenoid valve assembly.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

       Note: Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection .

    • Refer to Control Module References for control solenoid valve assembly replacement, set-up, and programming.
    • Perform the Transmission Adaptive Values Learn following all transmission related repairs.
   


© Copyright Chevrolet. All rights reserved