To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC B0967 or B0968

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0967 02: Parking Aid On/Off Switch Circuit Short To Ground

DTC B0968 00: Parking Aid On/Off Switch Indicator Circuit

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Parking Assist Switch Signal

B0967 02

1

--

--

Parking Assist Switch Indicator Control

B0968 00

1

B0968 00

-

Parking Assist Switch Ground

--

1

--

--

1. Parking Assist Switch Malfunction

Circuit/System Description

The parking assist can be activated/deactivated by pressing the parking assist switch. By engaging the drive or reverse gear the parking assist can also be activated. By subsequently pressing the parking assist switch the parking assist can be disabled again.

The indicator in the parking assist switch shows the status of the parking assist. If the lamp is ON, the parking assist is activated.

Conditions for Running the DTC

    • Ignition ON
    • The parking assist is activated. The activation takes place by putting in drive or reverse gear or by pressing the parking assist switch.

Conditions for Setting the DTC

B0967 02

The parking assist control module has detected a short to ground.

B0968 00

The parking assist control module has detected a circuit malfunction.

Action Taken When the DTC Sets

    • The parking assist is disabled.
    • The cluster displays service park assist symbol.

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

Object Detection Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Object Detection Description and Operation : C140/Long Body UFR or UD7 → C145/Short Body UFR → Rear Vision Camera → Holden Genuine Accessory(Aftermarket)

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Verify that DTC B0967 02 is not present.
  2. If DTC is present, refer to Parking Assist Switch Malfunction.
  3. Verify that B0968 00 is not present.
  4. If DTC is present, refer to Parking Assist Switch Indicator Malfunction.
  5. Activate and deactivate the parking assist switch and verify the scan tool Park Assist Switch parameter changes between Active and Inactive.

Circuit/System Testing

Parking Assist Switch Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48 multi-function switch module.
  2. Test for less than 10 Ω between the ground circuit terminal 16 and ground.
  3. If greater than the specified value, test the ground circuit for an open/high resistance.
  4. Connect the harness connector at the S48 multi-function switch module.
  5. Disconnect the X1 harness connector at the K86 advance parking assist control module.
  6. Ignition ON, test for less than 0.3 V between the signal circuit terminal 8 X1 and ground.
  7. If greater than the specified value, test the signal circuit for a short to voltage.
  8. Ignition ON, verify that a test lamp does not illuminate between the B+ circuit terminal 1 X1 and signal circuit terminal 8 X1.
  9. If the test lamp illuminates, test signal circuit for a short to ground. If the circuit tests normal, replace the S48 multi-function switch module.
  10. Verify that the test lamp illuminates between the B+ circuit terminal 1 X1 and signal circuit terminal 8 X1 while pressing the parking assist switch.
  11. If the test lamp does not illuminate, test the signal circuit for an open/high resistance. If all circuits test normal, replace the S48 multi-function switch module.
  12. If all circuits test normal, replace the K86 advance parking assist control module.

Parking Assist Switch Indicator Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48 multi-function switch module.
  2. Ignition ON, test for B+ between the ignition circuit terminal 1 and ground.
  3. If less than the specified value, test the ignition circuit for a short to ground or an open/high resistance.
  4. Command the Park Assist Switch LED output control ON with the scan tool. Test for B+ between the ignition circuit terminal 3 and the signal circuit terminal 12.
  5. If less than the specified value, test the signal circuit for an open/high resistance. If all circuits test normal, replace the K86 advance parking assist control module.
  6. Command the Park Assist Switch LED output control OFF with the scan tool. Test for less than 0.3 V between the ignition circuit terminal 1 and the signal circuit terminal 12.
  7. If greater than the specified value, test the signal circuit for a short to ground. If all circuits test normal, replace the K86 advance parking assist control module.
  8. If all circuits test normal, replace the S48 multi-function switch module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Driver Information Display Switch Replacement : Short Body
    • Control Module References for parking assist control module replacement, programming and set-up
   


© Copyright Chevrolet. All rights reserved