Service Information

Cruze

DTC B0283

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0283 02: Electric Rear Defrost Circuit Short To Ground

DTC B0283 05: Electric Rear Defrost Circuit Short To Battery or Open

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Rear Demist Relay Switch B+	1	1	--	--
Rear Demist Relay Control	B0283 02	B0283 05	B0283 05	--
Rear Demist Relay Coil Ground	--	B0283 05	--	--
1. Rear Demister Inoperative

When the HVAC control module receives a rear window demist request from the HVAC control faceplate, the HVAC control module will supply voltage to the relay coil. Battery positive voltage is supplied at all times to the relay switched input and the relay coil is always grounded. This allows battery positive voltage from the relay switched input to flow through the switch contacts and out the relay switched output to the rear window demister grid.

Conditions for Running the DTC

Battery voltage must be between 9-16 V.

Conditions for Setting the DTC

B0283 02

The HVAC control module detects a short to ground in the relay control circuit.

B0283 05

The HVAC control module detects a short to voltage or an open/high resistance in the relay control circuit.

Action Taken When the DTC Sets

•	If B0283 02 is current, the rear window demister grid will operate continuously.

•	If B0283 05 is current, the rear window demister grid will be inoperative.

Conditions for Clearing the DTC

•	The DTC will be current for as long as the fault is present.

•	When the fault is no longer present, the DTC will be a history DTC.

•	A history DTC will clear after 50 ignition cycles.

Reference Information

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Engine running, command the E18 rear window defogger grid ON and OFF with a scan tool. The E18 rear window defogger grid should turn ON and OFF when changing between the commanded states.

Circuit/System Testing

Ignition OFF, disconnect the K17 rear demist relay.
Test for less than 30 Ω between the ground circuit terminal 85 and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance

Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85.
Engine running, command the E18 rear window defogger grid ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K33 HVAC control module.

⇒	If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K33 HVAC control module.

If all circuits test normal, test or replace the K17 rear demist relay.

Component Testing

Relay Test

Ignition OFF, disconnect the K17 rear demist relay.
Test for 60-180 Ω between terminals 85 and 86.

⇒	If not within the specified range, replace the K17 rear demist relay.

Test for infinite resistance between the following terminals:

•

30 and 86

•

30 and 87

•

30 and 85

•

85 and 87

⇒	If not the specified value, replace the K17 rear demist relay.

Install a 25 A fused jumper wire between relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 Ω between terminals 30 and 87.

⇒	If greater than the specified range, replace the K17 rear demist relay.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

•	Relay Replacement

•	Control Module References for HVAC control module replacement, setup and programming