To the top of the document
Cruze
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Door Ajar Indicator Malfunction

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Left Front Door Ajar Switch Signal

2

1

1

--

Left Rear Door Ajar Switch Signal

2

1

1

--

Right Front Door Ajar Switch Signal

2

1

1

--

Right Rear Door Ajar Switch Signal

2

1

1

--

Driver Door Latch Ground

--

1

--

--

Passenger Door Latch Ground

--

1

--

--

Left Rear Door Latch Ground

--

1

--

--

Right Rear Door Latch Ground

--

1

--

--

1. Ajar Indicator Always Illuminated

2. Ajar Indicator Inoperative

Circuit/System Description

The driver window motor or driver window switch receives a discrete input from the driver door ajar switch signal circuit. The passenger window switch receives a discrete input from the passenger door ajar switch signal circuit. The body control module (BCM) or rear door window switches receive discrete inputs from each of the rear door ajar switch signal circuits. The door ajar switches are integral to each door latch assembly. When a door is opened, the normally open door ajar switch closes. With the door ajar switch closed, ground is provided to the door ajar switch signal circuit. The window switches and/or BCM interprets this and communicates via serial data with the instrument panel cluster.

Reference Information

Schematic Reference

Door Lock/Indicator Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Door Ajar Indicator Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification
  1. Ignition ON, observe the scan tool Body Control Module Driver Door Ajar Switch parameter while opening and closing the driver door. The parameter should change between Active and Inactive.
    2. ⇒If the value does not change, refer to Driver Door Ajar Switch Malfunction
  2. Observe the scan tool Body Control Module Passenger Door Ajar Switch parameter while opening and closing the front passenger door. The parameter should change between Active and Inactive.
    3. ⇒If the value does not change, refer to Passenger Door Ajar Switch Malfunction.
  3. Observe the scan tool Body Control Module Left Rear Door Ajar Switch and Right Rear Door Ajar Switch parameters while opening and closing the left and right rear doors. The parameters should change between Door Closed and Door Ajar.
    4. ⇒If the appropriate value does not change, refer to Rear Door Ajar Switch Malfunction.

Circuit/System Testing

Driver Door Ajar Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the A23D Door Latch Assembly - Driver.
  2. Test for less than 10 Ω between the ground circuit terminal 8 (Left Hand Drive) or terminal 3 (Right Hand Drive) and ground.
    3. ⇒If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect the harness connector at the S79D Window Switch - Driver.
  4. Ignition ON, verify the scan tool Driver Door Ajar Switch parameter is Inactive.
    5. ⇒If not the specified value, test the signal circuit terminal 6 (Left Hand Drive) or terminal 1 (Right Hand Drive) for a short to ground. If the circuit tests normal, replace the M74D Window Motor - Driver or S79D Window Switch - Driver.
  5. Install a 3 A fused jumper wire between the signal circuit terminal 6 (Left Hand Drive) or terminal 1 (Right Hand Drive) and ground. Verify the scan tool Driver Door Ajar Switch parameter is Active.
    6. ⇒If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the M74D Window Motor - Driver or S79D Window Switch - Driver.
  6. If all circuits test normal, test or replace the A23D Door Latch Assembly - Driver.

Passenger Door Ajar Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the A23P Door Latch Assembly - Passenger.
  2. Test for less than 10 Ω between the ground circuit terminal 3 (Left Hand Drive) or terminal 8 (Right Hand Drive) and ground.
    3. ⇒If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect the harness connector at the S79P Window Switch - Passenger.
  4. Ignition ON, verify the scan tool Passenger Door Ajar Switch parameter is Inactive.
    5. ⇒If not the specified value, test the signal circuit terminal 1 for a short to ground. If the circuit tests normal, replace the S79P Window Switch - Passenger.
  5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground. Verify the scan tool Passenger Door Ajar Switch parameter is Active.
    6. ⇒If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the S79P Window Switch - Passenger.
  6. If all circuits test normal, test or replace the A23P Door Latch Assembly - Passenger.

Rear Door Ajar Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the appropriate rear door latch.
  2. Test for less than 10 Ω between the ground circuit terminal listed below and ground:
    3. • Left rear door latch ground circuit terminal 6
    • Right rear door latch ground circuit terminal 3
    ⇒If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect the harness connector at the rear window switch.
  4. Ignition ON, verify the appropriate scan tool Rear Door Ajar Switch parameter is Inactive.
    5. ⇒If not the specified value, test the signal circuit terminal listed below for a short to ground. If the circuit tests normal, replace the K9 Body Control Module or rear window switch.
  5. Install a 3 A fused jumper wire between the signal circuit terminal listed below and ground. Verify the scan tool Rear Door Ajar Switch parameter is Active.
    6. • Left rear door ajar switch signal circuit terminal 4
    • Right rear door ajar switch signal circuit terminal 1
    ⇒If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module or rear window switch.
  6. If all circuits tests normal, test or replace the rear door latch.

Component Testing

Dynamic Test

  1. Ignition OFF, disconnect the harness connector at the appropriate door latch.
  2. With the switch in the open position (door catch closed), test for infinite resistance between the signal and the ground terminals listed below:
    3. • Left-hand drive: Driver door latch signal terminal 6 and ground terminal 8
    • Right-hand drive: Driver door latch signal terminal 1 and ground terminal 3
    • Left-hand drive: Passenger door latch signal terminal 1 and ground terminal 3
    • Right-hand drive: Passenger door latch signal terminal 6 and ground terminal 8
    • Left rear door latch signal terminal 4 and ground terminal 6
    • Right rear door latch signal terminal 1 and ground terminal 3
    ⇒If not the specified value, replace the door latch.
  3. With the switch in the closed position (door catch open), test for less than 1 Ω between the signal and the ground terminals listed below:
    4. • Left-hand drive: Driver door latch signal terminal 6 and ground terminal 8
    • Right-hand drive: Driver door latch signal terminal 1 and ground terminal 3
    • Left-hand drive: Passenger door latch signal terminal 1 and ground terminal 3
    • Right-hand drive: Passenger door latch signal terminal 6 and ground terminal 8
    • Left rear door latch signal terminal 4 and ground terminal 6
    • Right rear door latch signal terminal 1 and ground terminal 3
    ⇒If greater than the specified range, replace the door latch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Front Side Door Catch Replacement
    •  Rear Side Door Catch Replacement
    •  Front Side Door Window Regulator Motor Replacement
    •  Control Module References
   


© Copyright Chevrolet. All rights reserved