To the top of the document
Volt
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Electronic Brake Control Module Scan Tool Information

Table 1: Electronic Brake Control Module Scan Tool Data Parameters
Table 2: Electronic Brake Control Module Scan Tool Output Controls

The electronic brake control module (EBCM) scan tool data parameters list contains all ABS related parameters that are available on the scan tool. The list is arranged in alphabetical order. A given parameter may appear in any one of the data lists.

Electronic Brake Control Module Scan Tool Data Parameters

Parameter

System State

Expected Value

Description

Operating Conditions: Vehicle in Service Mode

ABS Pump Motor Voltage

-

Varies

The scan tool displays the pump motor voltage.

Antilock Braking System

-

Inactive

The scan tool displays Inactive or Active. Active is displayed when the antilock braking system is in traction control event.

Antilock Braking System Status

-

No

The scan tool displays No or Yes. If there is an ABS malfunction the scan tool will display Yes.

Brake Controls Brake Pedal Position Sensor Circuit 1

-

Varies

This displays volts. This is the brake controls brake pedal position sensor circuit 1 reference value.

Brake Controls Brake Pedal Position Sensor Circuit 2

-

Varies

This displays percentage. This is the brake controls brake pedal position sensor circuit 2 that calculates the percentage of brake pedal applied or released.

Brake Controls Brake Pedal Position Sensor without Offset

-

Varies

This displays mm. This is the value used to compare the position of the primary piston sensors.

Brake Controls Brake Pedal Position Sen. 5 Volt Supply Voltage

-

Varies

This displays volts. This is the voltage supply to the brake controls brake pedal position sensor.

Brake Controls Brake Pedal Position

-

Varies

The scan tool displays the brake pedal counts. Learned or Not Learned. This is the brake controls brake pedal position sensor zeroed or learned value.

Brake Boost Power Status

-

Enabled

The scan tool displays Enabled or Disabled.

Brake Master Cylinder Pressure Sensor

-

Varies

This displays psi/kpa. This is the current brake applied pressure.

Brake Fluid Level Sensor

-

Varies

This displays volts. This is the voltage supply to the brake fluid level sensor signal.

Brake Pedal Position Sensor Signal

Brake pedal released

Released

The scan tool displays Applied or Release depending on the state of the brake pedal.

Brake pedal applied

Applied

Brake Pressure Sensor

Brake pedal released

0-1.55 V

The scan tool displays 0-5 V depending on the applied hydraulic brake pressure.

Brake pedal applied

1.55-5 V

Dynamic Rear Proportioning Status

-

No

The scan tool displays No or Yes. If the EBCM disables the dynamic rear proportioning due to a fault the scan tool will display Yes.

Engine Drag Control Status

-

No

The scan tool displays No or Yes. If the EBCM detects an ABS event, it sends a signal to the ECM to reduce engine power and Yes is displayed on the scan tool.

High Pressure Accumulator Sensor

-

Varies

This displays the pressure of the accumulator.

Ignition Voltage

-

Varies

This displays volts. This is the voltage status of the electronic brake control module (EBCM).

Left Front Inlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the left front inlet solenoid valve is commanded ON.

Left Front Outlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the left front outlet solenoid valve is commanded ON.

Left Front Wheel Speed Sensor

-

0 km/h (0 MPH)

The scan tool displays km/h (MPH) depending on the current speed of the left front wheel speed sensor.

Left Rear Inlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the left rear inlet solenoid valve is commanded ON.

Left Rear Outlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the left rear outlet solenoid valve is commanded ON.

Left Rear Wheel Speed Sensor

-

0 km/h (0 MPH)

The scan tool displays km/h (MPH) depending on the current speed of the left rear wheel speed sensor.

Panic Brake Assist Status

-

No

The scan tool displays No or Yes. If the EBCM disables the panic brake assist due to a fault the scan tool will display Yes.

Regenerative Braking Status

-

Active

The scan tool displays Active or Inactive.

Right Front Inlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the right front inlet solenoid valve is commanded ON.

Right Front Outlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the right front outlet solenoid valve is commanded ON.

Right Front Wheel Speed Sensor

-

0 km/h (0 MPH)

The scan tool displays km/h (MPH) depending on the current speed of the right front wheel speed sensor.

Right Rear Inlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the right rear inlet solenoid valve is commanded ON.

Right Rear Outlet Solenoid Valve Command

-

Off

The scan tool displays Off or On. On is displayed when the right rear outlet solenoid valve is commanded ON.

Right Rear Wheel Speed Sensor

-

0 km/h (0 MPH)

The scan tool displays km/h (MPH) depending on the current speed of the right rear wheel speed sensor.

Steering Wheel Angle Sensor Signal

Steering wheel in straight position

-5 to +5°

The scan tool displays °. This is the current position of the steering angle sensor.

Steering wheel turned left until stop

450-550°

Steering wheel turned right until stop

-550 to -450°

System Voltage

-

11-14 V

The scan tool displays V. This is the current battery voltage.

Traction Control System

-

No

The scan tool displays No or Yes. If there is a traction control malfunction the scan tool displays Yes.

Vehicle Stability System Status

-

No

The scan tool displays No or Yes. If there is a stability control malfunction the scan tool displays Yes.

Electronic Brake Control Module Scan Tool Output Controls

Output Control

Description

Automated Brake Bleed

This is used in order to bleed ABS hydraulics.

ABS Pump Motor

This is used in order to command the ABS pump motor On or Off.

   


© Copyright Chevrolet. All rights reserved