Volt |
||||||||
|
|
|
|||||||
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | U183C | U183C | -- | -- |
Ignition | U183C | U183C | -- | -- |
Accessory Wake Up Serial Data | U1814, U2099 | U183C | -- | -- |
Powertrain High-Speed GMLAN Serial Data (+) | U0074* | U0074, U183C* | U0074* | - |
Powertrain High-Speed GMLAN Serial Data (-) | U0074* | U0074, U183C* | U0074* | -- |
Ground | -- | U183C | -- | -- |
* Other DTCs may set with this fault | ||||
The serial data circuit is the means by which the control modules in the vehicle communicate with each other. When the vehicle is ON, each control module communicating on the serial data circuit sends a state of health (SOH) message to ensure that the control module is operating properly. When hybrid powertrain control module 2 stops communicating on the serial data circuit, for example if the hybrid powertrain control module 2 loses power or earth, the SOH message it normally sends on the serial data circuit disappears. Other control modules on the serial data circuit, which expect to receive that SOH message, detect its absence; those control modules in turn set a DTC associated with the loss of SOH of the hybrid powertrain control module 2. A loss of serial data communications DTC does not represent a failure of the control modules that contain the stored code.
The auxiliary transmission fluid pump control module is controlled by drive motor 3 control module. The communication for auxiliary transmission fluid pump control module and all drive motor control modules is handled through the hybrid powertrain control module 1. The auxiliary transmission fluid pump control module and the hybrid powertrain control module 1 are all internal to the power inverter module. All circuits to the auxiliary transmission fluid pump control module and hybrid powertrain control module 1 are also internal to the power inverter module. Communication diagnostics for the serial data, including control module power and earth as well as the wake-up circuits, for auxiliary transmission fluid pump control module and the hybrid powertrain control module 1 are all diagnosed from external sources only to the power inverter module connector.
The system voltage is at least 10 V.
A supervised periodic message that includes the transmitter module availability has not been received.
The DTC U183C is a type B DTC.
The DTC U183C is a type B DTC.
| • | Sometimes, while diagnosing a specific customer concern or after a repair, you may notice a history U-code present. However, there is no associated "current" or "active" status. Loss-of- communication U-codes such as these can set for a variety of reasons. Many times, they are transparent to the vehicle operator and technician, and/or have no associated symptoms. Eventually, they will erase themselves automatically after a number of fault-free ignition cycles. This condition would most likely be attributed to one of these scenarios: |
| - | A control module on the data communication circuit was disconnected while the communication circuit is awake. |
| - | Power to one or more control modules was interrupted during diagnosis. |
| - | A low battery condition was present, so some control modules stop communicating when battery voltage drops below a certain threshold. |
| - | Battery power was restored to the vehicle and control modules on the communication circuit did not all re-initialise at the same time. |
| - | If a loss-of-communication U-code appears in history for no apparent reason, it is most likely associated with one of the scenarios above. These are all temporary conditions and should never be interpreted as an intermittent fault, causing you to replace a part. |
| • | A control module may have a U-code stored in history that does not require any repairs. Issues with late or corrupted messages between control modules can be temporary with no apparent symptom or complaint; this does not mean the control module is faulty. Do not replace a control module based only on a history U-code. |
| • | Do not replace a control module reporting a U-code. The U-code identifies which control module needs to be diagnosed for a communication issue. |
| • | Communication may be available between the control module and the scan tool with one or more GMLAN serial data systems inoperative. This condition is due to the control module using multiple GMLAN busses. |
| • | Use Data Link References to determine what GMLAN serial data communications the non communicating control module uses. |
| • | The control module may not have internal protection for specific control circuits and may open a B+ or ignition fuse. If a fuse is open and the B+ or ignition circuit is not shorted to ground, ensure none of the control circuits are shorted to ground before replacing the control module. |
Data Link Communications Description and Operation
Control Module References for scan tool information
Verify that DTC U0074, U1814, U2099, B1428, B1370, B1380, B1440, B1441, B1325 or P0562 is not set.
| ⇒ | If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle . |
Note: Use the schematic to identify the following: • The control module location on the powertrain high-speed GMLAN serial data circuits • The control module B+, ignition, earth, accessory wake-up serial data and serial data circuit terminals
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the control circuits of the K114B hybrid powertrain control module 2 for a short-circuit to earth. If the circuits test normal, replace the K114B hybrid powertrain control module 2. |
| ⇒ | If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the control circuits of the K114B hybrid powertrain control module 2 for a short-circuit to earth. If the circuits test normal, replace the K114B hybrid powertrain control module 2. |
| ⇒ | If the test lamp does not illuminate, test the entire circuit, including the B+ circuit to the K9 body control module (BCM), for an open-circuit/high resistance or a short-circuit to earth. If the circuits test normal, replace the K9 BCM. |
| ⇒ | If greater than the specified range, test the serial data circuit for an open/high-resistance between the K114B hybrid powertrain control module 2 and the T6 power inverter module. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for control module replacement, programming and setup |
| ©© Copyright Chevrolet. All rights reserved |
