To the top of the document
Volt
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC P0CD6-P0CD8

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0CD6: Hybrid/EV Battery Pack Coolant Temperature Sensor 2 Performance

DTC P0CD7: Hybrid/EV Battery Pack Coolant Temperature Sensor 2 Circuit Low Voltage

DTC P0CD8: Hybrid/EV Battery Pack Coolant Temperature Sensor 2 Circuit High Voltage

Circuit/System Description

The hybrid/EV battery has 2 hybrid/EV battery pack coolant temperature sensors. The hybrid/EV battery pack coolant temperature sensors are located in the coolant inlet (sensor 1) and the outlet (sensor 2) of the hybrid/EV battery. The temperature sensor is a variable resistor that measures the temperature of the hybrid/EV battery coolant. The hybrid/EV battery pack coolant temperature sensor resistance changes with battery coolant temperature. The lower the temperature, the higher the resistance of the sensor. The higher the temperature, the lower the resistance of the sensor. The battery energy control module (BECM) uses the hybrid/EV battery temperature sensors to determine the hybrid/EV battery pack temperature to control the battery cooling operation.

Conditions for Running the DTC

P0CD6

    • The hybrid/EV powertrain control module 2 is awake and communicating.
    • The 12 V battery voltage is greater than or equal to 9 V.
    • None of the following DTCs are set: P0C47, P0C4A, P0CD7, P0CD8, U185B, or U2602.
    • The coolant pump speed is greater than 20%.

P0CD7

    • The 12 V battery voltage is greater than or equal to 9 V.
    • The battery energy control module is awake and communicating.
    • DTC P1A07 is not set.

P0CD8

    • The 12 V battery voltage is greater than or equal to 9 V.
    • The battery energy control module is awake and communicating.
    • DTC P1A07 is not set.

Conditions for Setting the DTC

P0CD6

The hybrid/EV battery pack coolant temperature sensor 2 is not within 20°C (36°F) of the hybrid/EV battery pack coolant temperature sensor 1 and the Average Hybrid/EV Battery Pack Temperature.

P0CD7

The coolant temperature 2 is greater than or equal to 87.5°C (189.5°F).

P0CD8

The coolant temperature 2 is less than or equal to -40°C (-40°F).

Action Taken When the DTC Sets

DTC P0CD6-P0CD8 are type B DTCs.

Conditions for Clearing the DTC

DTC P0CD6-P0CD8 are type B DTCs.

Diagnostic Aids

    • Low or no coolant in the system may set a DTC P0CD6.
    • The hybrid/EV powertrain control module 2 will use battery pack cell temperatures as a default.

Reference Information

Schematic Reference

Hybrid Cooling Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Hybrid Cooling System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

EL-48900 HEV Safety Kit

For equivalent regional tools, refer to Special Tools .

Circuit/System Verification

  1. Vehicle in Service Mode, observe the scan tool Hybrid\EV Battery Pack Coolant Temperature Sensor 2 parameter. The readings should be between -39°C and +85°C (-38.2°F and +185°F).
  2. Compare the Hybrid\EV Battery Pack Coolant Temperature Sensor 2 and Hybrid\EV Battery Pack Coolant Temperature Sensor 1 parameters. The sensor readings should be within 20°C (36°F) of each other.

Circuit/System Testing

Danger: High voltage enabling and disabling shall be only performed by High Voltage Qualified Technicians. The procedures for high-voltage enabling/disabling can be found in the service instructions and must be strictly followed at all times. The usage of the Protocol High Voltage Disabling/Enabling is mandatory. The High-Voltage Qualified Technician is responsible for the adherence to the manufacturer's service instructions as well as current national legal regulations.

Failure to follow the procedures exactly as written may result in serious injury or death.

Questions regarding training can be answered by your national training centre.

Danger: Any hybrid/EV battery pack replacement shall be performed by High-Voltage Qualified Technicians only. The replacement procedure can be found in the service instruction and must be strictly followed at all times. The High-Voltage Qualified Technician is responsible for adherence to the manufacturer's service instructions as well as current national legal regulations. If the hybrid/EV battery pack needs to be replaced contact the Technical Assistance Centre for further instructions prior to removal of the battery pack.

  1. Vehicle in Service Mode, verify that DTC P0AC1, P0B10, P0C44, P0C47, P0C4A or P1F18 is not set.
  2. If any DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .
  3. If DTC P0CD6, P0CD7, or P0CD8 is set, replace the A4 hybrid/EV battery pack.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

    •  Drive Motor Battery Replacement and Shipping Preparation
    • Control Module References for battery energy control module replacement and hybrid battery interface control modules 1-4, programming and set-up for the hybrid/EV battery pack replacement.
   


&#169© Copyright Chevrolet. All rights reserved