To the top of the document
Volt
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC U2105-U2199

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using the diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

Refer to Control Module U Code List .

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Module B+

U2105-U2199

U2105-U2199

--

--

Module Ignition

U2105-U2199

U2105-U2199

--

--

Accessory Wakeup Serial Data

U1814

U2105-U2199

--

--

Serial Data Communication Enable

U2099

U2105-U2199

--

--

Accessory Wake Up Serial Data 2

P06E4

U2105-U2199

--

--

Low Speed GMLAN Serial Data

1

U2105-U2199

1

--

High Speed GMLAN Serial Data (+)

2

U2105-U2199

2

--

High Speed GMLAN Serial Data (-)

2

U2105-U2199

2

--

Chassis High Speed GMLAN Serial Data (+)

3

U2105-U2199

3

-

Chassis High Speed GMLAN Serial Data (-)

3

U2105-U2199

3

--

Module Ground

-

U2105-U2199

--

--

1. Scan tool does not communicate with low speed GMLAN device

2. Scan tool does not communicate with high speed GMLAN device

3. Scan tool does not communicate with chassis high speed GMLAN device

Circuit/System Description

Control modules connected to the high and low speed GMLAN serial data circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the control modules. The control modules have prerecorded information about what messages are needed to be exchanged on the serial data circuits, for each virtual network. The messages are supervised and also, some periodic messages are used by the receiver module as an availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

Conditions for Running the DTC

    • The system voltage is between 9–16 V.
    • The vehicle power mode requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

The control module uses a default value for the missing parameters.

Conditions for Clearing the DTC

    • A current DTC clears when the malfunction is no longer present.
    • A history DTC clears when the control module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Diagnostic Aids

    • Sometimes, while diagnosing a specific customer concern or after a repair, you may notice a history U-code present. However, there is no associated "current" or "active" status. Loss-of- communication U-codes such as these can set for a variety of reasons. Many times, they are transparent to the vehicle operator and technician, and/or have no associated symptoms. Eventually, they will erase themselves automatically after a number of fault-free ignition cycles. This condition would most likely be attributed to one of these scenarios:
       - A control module on the data communication circuit was disconnected while the communication circuit is awake.
       - Power to one or more control modules was interrupted during diagnosis.
       - A low battery condition was present, so some control modules stop communicating when battery voltage drops below a certain threshold.
       - Battery power was restored to the vehicle and control modules on the communication circuit did not all re-initialise at the same time.
       - If a loss-of-communication U-code appears in history for no apparent reason, it is most likely associated with one of the scenarios above. These are all temporary conditions and should never be interpreted as an intermittent fault, causing you to replace a part.
    • A control module may have a U-code stored in history that does not require any repairs. Issues with late or corrupted messages between control modules can be temporary with no apparent symptom or complaint; this does not mean the control module is faulty. Do not replace a control module based only on a history U-code.
    • Do not replace a control module reporting a U-code. The U-code identifies which control module needs to be diagnosed for a communication issue.
    • Use Data Link References to determine what GMLAN serial data communications the non communicating control module uses.
    • Some control modules may not have internal protection for specific voltage outputs and may open a battery positive voltage or ignition voltage source fuse. If a voltage input fuse is open and no short is found in that circuit, ensure that no control module output voltage circuit is shorted to ground before replacing the control module.
    • Some intermittent communication concerns may be caused by fretting corrosion on the serial data circuit terminals. Inspect all connectors at the control module that set the communication DTC, the control module that the communication DTC was set against and any in-line harness connectors between the two control modules. Do not replace a control module based only on fretting corrosion. Refer to bulletin 09-06-03-004 for assistance with the diagnosis and repair of this condition..
    • This diagnostic can be used for any control module that should communicate with high or low speed GMLAN serial data providing the vehicle is equipped with the option that uses that control module.

Reference Information

    •  Data Communication Schematics
    •  Control Module References

Connector End View Reference

Component Connector End Views

Description and Operation

Data Link Communications Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool References

Control Module References for scan tool information

Circuit/System Verification

  1. Determine the control module that is not communicating. Refer to Control Module U Code List .
  2. Verify that DTC U0073, U0074, U0077, U0078, U007A, P06E4, P1EB9, U1814, U2099, B1325, B1330, B1370, B1380, B1424, B1428, B1440, B1441, B1517, C0800, C0899, C12E1, P0560, or P0562 is not set.
  3. If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .

Circuit/System Testing

Note: Terminal and connector identifiers will be different depending on the individual control module being tested. Use Schematic Reference and Connector End View Reference to determine the control module's connector and B+, ignition, earth, accessory wake-up serial data, accessory wake-up serial data 2, serial data communication enable and serial data circuit terminals.

  1. Vehicle OFF, disconnect the harness connector at the control module that is not communicating.
  2. Test for less than 10 Ω between each ground circuit terminal and ground.
  3. If greater than specified range, test the ground circuit for an open/high resistance.
  4. If equipped, vehicle in Service Mode, verify that a test lamp illuminates between each B+ circuit terminal and earth.
  5. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the control circuits of the control module for a short to ground. If the circuits test normal, replace the appropriate control module.
  6. If equipped, vehicle in Service Mode, verify that a test lamp illuminates between each ignition circuit terminal and earth.
  7. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the control circuits of the control module for a short to ground. If the circuits test normal, replace the appropriate control module.

    Note: Only the high-speed GMLAN modules have a serial data communication enable circuit OR an accessory wake-up serial data circuit OR an accessory wake-up serial data 2 circuit. Either the K9 body control module or the K114B hybrid power train control module 2 is the output for these circuits. Refer to the control module schematics to identify which control modules have these circuits and which control module is the output for these circuits. If the control module that is not communicating does not have any of these circuits, proceed to the next step.

  8. If equipped, vehicle in Service Mode, verify that a test lamp illuminates between the serial data communication enable circuit terminal OR the accessory wake-up serial data circuit terminal coming from the K9 body control module and earth.
  9. If the test lamp does not illuminate, test the entire circuit, including the B+ circuit to the K9 body control module, for an open-circuit/high resistance or short-circuit to earth. If the circuits test normal, replace the K9 body control module.
  10. If equipped, vehicle in Service Mode, verify that a test lamp illuminates between the accessory wake-up serial data 2 circuit terminal coming from K114B hybrid powertrain control module 2 and earth.
  11. If the test lamp does not illuminate, test the entire circuit, including the B+ circuit to the K114B hybrid powertrain control module 2, for an open-circuit/high resistance or short-circuit to earth. If the circuits test normal, replace the K114B hybrid powertrain control module 2.
  12. Vehicle OFF, disconnect the harness connector at the control module setting the DTC.
  13. Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 metres away from vehicle. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 2 Ω in each GMLAN serial data circuit between the non-communicating control module and the control module setting the DTC.
  14. If greater than the specified range, test the serial data circuit for an open-circuit/high resistance between the non communicating control module and the control module setting the DTC.
  15. If all circuits test normal, replace the control module that is not communicating.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  GMLAN Wiring Repairs
    • Control Module References for control module replacement, setup, and programming
   


&#169© Copyright Chevrolet. All rights reserved