To the top of the document
Volt
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Cellular Telephone Charging Malfunction

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

12V Reference

1

1

--

--

Cradle Signal 1

--

--

--

--

Cradle Signal 2

--

--

--

--

Low Reference

--

1

1

--

1. Charging Inoperative

Circuit/System Description

The mobile telephone control module uses the cradle to charge the cellular telephone.

Reference Information

Schematic Reference

Cellular Telephone Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Cellular Telephone Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References

Circuit/System Verification

Vehicle ON, connect the mobile phone to the cradle observe the scan tool Phone in Cradle parameter. The reading should be Yes.

⇒If the reading is No, refer to Connecting Malfunction.
⇒If the reading is Yes, refer to Charging Inoperative.

Circuit/System Testing

Note: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

Connecting Malfunction

  1. Vehicle OFF, disconnect the X2 connector at the K82 Mobile Telephone Control Module and the X1 connector at the X91 Mobile Telephone Connector.
  2. Vehicle ON, test for less than 0.3 V between the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module and ground.
    3. ⇒If greater than the specified range, test the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module for a short to voltage.
  3. Vehicle ON, test for less than 0.3 V between the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module and ground.
    4. ⇒If greater than the specified range, test the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module for a short to voltage.
  4. Vehicle OFF, test for infinite resistance between the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module and ground.
    5. ⇒If less than the specified range, test the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module for a short to ground.
  5. Vehicle OFF, test for infinite resistance between the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module and ground.
    6. ⇒If less than the specified range, test the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module for a short to ground.
  6. Vehicle OFF, test for less than 5 Ω between the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module and the signal circuit terminal 10 X1 at the X91 Mobile Telephone Connector.
    7. ⇒If less than the specified range, test the signal circuit terminal 13 X2 at the K82 Mobile Telephone Control Module for an open/high resistance.
  7. Vehicle OFF, test for less than 5 Ω between the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module and the signal circuit terminal 2 X1 at the X91 Mobile Telephone Connector.
    8. ⇒If less than the specified range, test the signal circuit terminal 15 X2 at the K82 Mobile Telephone Control Module for an open/high resistance.
  8. If all circuits test normal, replace the X91 Mobile Telephone Connector and verify that the customer concern is not still present.
    9. ⇒If the customer concern is still present, replace the K82 Mobile Telephone Control Module.

Charging Inoperative

  1. Vehicle OFF, disconnect the X1 and X2 connector at the K82 Mobile Telephone Control Module.
  2. Vehicle OFF, test for less than 5 Ω between the low reference circuit terminal 2 X1 and ground.
    3. ⇒If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K82 Mobile Telephone Control Module.
  3. Vehicle ON, test for greater than 11 V between the 12 V reference circuit terminal 1 X1 and ground.
    4. ⇒If less than the specified range, test the 12 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K82 Mobile Telephone Control Module.
  4. Vehicle ON, test for less than 0.3 V between the low reference circuit terminal 8 X2 at the K82 Mobile Telephone Control Module and ground.
    5. ⇒If greater than the specified range, test the low reference circuit terminal 8 X2 at the K82 Mobile Telephone Control Module for a short to voltage.
  5. Vehicle ON, test for less than 0.3 V between the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module and ground.
    6. ⇒If greater than the specified range, test the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module for a short to voltage.
  6. Vehicle OFF, test for infinite resistance between the low reference circuit terminal 8 X2 at the K82 Mobile Telephone Control Module and ground.
    7. ⇒If less than the specified range, test the low reference circuit terminal 8 X2 at the K82 Mobile Telephone Control Module for a short to ground.
  7. Vehicle OFF, test for infinite resistance between the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module and ground.
    8. ⇒If less than the specified range, test the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module for a short to ground.
  8. Vehicle OFF, test for less than 5 Ω between the signal circuit terminal 8 X2 at the K82 Mobile Telephone Control Module and the signal circuit terminal 4 X1 at the X91 Mobile Telephone Connector.
    9. ⇒If less than the specified range, test the signal circuit terminal 8 X2 at the K82 Mobile Telephone Control Module for an open circuit/high resistance.
  9. Vehicle OFF, test for less than 5 Ω between the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module and the signal circuit terminal 8 X1 at the X91 Mobile Telephone Connector.
    10. ⇒If less than the specified range, test the signal circuit terminal 16 X2 at the K82 Mobile Telephone Control Module for an open/high resistance.
  10. If all circuits test normal, replace the X91 Mobile Telephone Connector and verify that the customer concern is not still present.
    11. ⇒If the customer concern is still present, replace the K82 Mobile Telephone Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for remote control door lock receiver replacement, programming and setup

   


&#169© Copyright Chevrolet. All rights reserved