To the top of the document
Captiva
To Previous PageTo Next Page
GMDE Start PageLoad static TOCLoad dynamic TOCHelp?

SECTION

MAINTENANCE AND REPAIR

ON-VEHICLE SERVICE


C7A19E01
Display graphicTranslations of text in graphics


Cigar Jack

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the front console retainer. Refer to Section 9G, Interior Trim.
  3. Remove the front console cover trim panel.
  4. Disconnect the electrical connectors.

C7A19E01
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the front console cover in the gear lever cover.
  2. Connect the electrical connector.
  3. Install the front console retainer. Refer to Section 9G, Interior Trim.

    4. Tighten
    Tighten the front console screws to 2 N•m (18 lb-in).


C7A19E02
Display graphicTranslations of text in graphics


Instrument Panel Steering Colum Opening Pillar

Removal Procedure

  1. Remove the hood prime latch release handle. Refer to Section 9R, Body Front End.
  2. Remove the screw and the instrument panel steering column opening pillar.

C7A19E02
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the instrument panel steering column opening pillar.

    2. Tighten
    Tighten the instrument panel steering column opening pillar screw to 2 N•m (18 lb-in).

  2. Install the hood prime latch release handle. Refer to Section 9R, Body Front End.

C7A19E14
Display graphicTranslations of text in graphics


Instrument Panel Vent-Driver

Removal Procedure

  1. Remove the instrument cluster side cover.
  2. Remove the instrument cluster dimmer/headlamp leveling/mirror control switch assembly. Refer to " Instrument Cluster Dimmer/Headlamp Leveling Mirror Control Switch " in this section.
  3. Pry off the vents by inserting a screwdriver.

C7A19E14
Display graphicTranslations of text in graphics


Installation

  1. Press the vents onto the housing.
  2. Install the instrument cluster side cover.
  3. Install the instrument cluster dimmer/headlamp leveling/mirror control switch assembly. Refer to " Instrument Cluster Dimmer/Headlamp Leveling Mirror Control Switch " in this section.

C8A19E01
Display graphicTranslations of text in graphics


Instrument Panel Vent-Passenger

Removal Procedure

  1. Remove the instrument compartment. Refer to "Instrument Compartment" in this section.
  2. Remove the screws and I/P passenger molding.
  3. Pry off the vents by inserting a screwdriver.

C8A19E01
Display graphicTranslations of text in graphics


Installation

  1. Press the vents onto the housing.
  2. Install I/P passenger molding with screws.
  3. Install the instrument compartment. Refer to "Instrument Compartment" in this section.

C7A19E03
Display graphicTranslations of text in graphics


Instrument Compartment

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the screws at the base of the instrument compartment.
  3. Open and remove the screws.
  4. Disconnect the electrical connector.
  5. Remove the instrument compartment.

C7A19E03
Display graphicTranslations of text in graphics


Installation Procedure

  1. Position the instrument compartment in the instrument panel.
  2. Connect the negative battery cable.
  3. Install the instrument compartment with the screws.

    4. Tighten
    Tighten the instrument compartment screws to 2 N•m (18 lb-in).

  4. Connect the negative battery cable.

C7A19E12
Display graphicTranslations of text in graphics


Digital Clock

Removal Procedure

  1. Remove the I/P center trim panel.
  2. Remove the screws and I/P ACC bezel.
  3. Remove the screws and the digital clock.

C7A19E12
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the digital clock with the screws.

    2. Tighten
    Tighten the digital clock screws to 2 N•m (18 lb-in).

  2. Install the I/P ACC bezel with the screws.
  3. Install the I/P center cluster trim panel.

C8A19E02
Display graphicTranslations of text in graphics


Instrument Cluster

Removal Procedure

  1. Remove the steering column covers. Refer to Section 6E. Steering Wheel and Column.
  2. Remove the instrument cluster dimmer/headlamp leveling/mirror control switch. Refer to "Instrument Cluster Dimmer/Headlamp Leveling/mirror Control Switch" in this section.
  3. Remove the I/P center trim panel-left.
  4. Remove the screw and the I/P center molding.

    5. C7A19E04
    Display graphicTranslations of text in graphics


  5. Remove the screws and the instrument cluster housing.

    6. C8A19E03
    Display graphicTranslations of text in graphics


  6. Remove the screws and the instrument cluster.

C8A19E03
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the instrument cluster with the screws.

    2. Tighten
    Tighten the instrument cluster screws to 2 N•m (18 lb-in).


    C7A19E04
    Display graphicTranslations of text in graphics


  2. Install the instrument cluster housing with the screws.

    3. Tighten
    Tighten the instrument cluster housing screws to 2 N•m (18 lb-in).


    C8A19E02
    Display graphicTranslations of text in graphics


  3. Install the I/P center molding with screws.
  4. Install the I/P center trim panel-left.
  5. Install the instrument cluster dimmer/headlamp leveling/mirror control switch. Refer to "Instrument Cluster Dimmer/Headlamp Leveling/mirror Control Switch" in this section.
  6. Install the steering column covers. Refer to Section 6E. Steering Wheel and Column.

C7A19E10
Display graphicTranslations of text in graphics


Instrument Cluster Dimmer/Headlamp Leveling/Mirror Control Switch

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the instrument cluster steering colum opening pillar.
  3. Remove the screw and the instrument cluster dimmer/headlamp leveling/mirror control switch.
  4. Disconnect the electrical connectors.

C7A19E10
Display graphicTranslations of text in graphics


Installation Procedure

  1. Replace the appropriate switch.
  2. Connect the electrical connectors.
  3. Install the instrument cluster dimmer/headlamp leveling/mirror control switch with the screw.

    4. Tighten
    Tighten the instrument cluster dimmer/headlamp leveling/mirror control switch screws to 2 N•m (18 lb-in).

  4. Install the instrument cluster steering colum opening pillar.
  5. Connect the negative battery cable.

C7A19F01
Display graphicTranslations of text in graphics


Driver Information Center

Removal Procedure

  1. Remove the instrument panel center trim panel.

    2. C7A19F05
    Display graphicTranslations of text in graphics


  2. Remove the screws and the instrument panel accessory bezel.

    3. C7A19E17
    Display graphicTranslations of text in graphics


  3. Remove the screws and the driver information center.

C7A19E17
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the driver information center with the screws.

    2. Tighten
    Tighten the driver information center with the screws to 2 N•m (18 lb-in).


    C7A19F05
    Display graphicTranslations of text in graphics


  2. Install the instrument panel accessory bezel with the screws.

    3. Tighten
    Tighten the instrument panel accessory bezel with the screws to 2 N•m (18 lb-in).


    C7A19F01
    Display graphicTranslations of text in graphics


  3. Install the instrument panel center trim panel.

C7A19F01
Display graphicTranslations of text in graphics


Instrument Panel Lower Compartment

Removal Procedure

  1. Remove the instrument panel center trim panel.

    2. C7A19F05
    Display graphicTranslations of text in graphics


  2. Remove the screws and the instrument panel accessory bezel.

    3. C7A19E18
    Display graphicTranslations of text in graphics


  3. Remove the screws and the instrument panel lower compartment.

C7A19E18
Display graphicTranslations of text in graphics


Installation Procedure

    Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.

  1. Install the instrument lower compartment with the screws.

    2. Tighten
    Tighten the instrument lower compartment with the screws to 2 N•m (18 lb-in).


    C7A19F05
    Display graphicTranslations of text in graphics


  2. Install the instrument panel accessory bezel with the screws.

    3. Tighten
    Tighten the instrument panel accessory bezel with the screws to 2 N•m (18 lb-in).


    C7A19F01
    Display graphicTranslations of text in graphics


  3. Install the instrument panel center trim panel.

C7A19E10
Display graphicTranslations of text in graphics


Instrument Panel

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the front, rear floor console. Refer to Section 9G, Interior Trim.
  3. Remove the instrument cluster dimmer/headlamp leveling/mirror control switch assembly. Refer to "Instrument Cluster Dimmer/Headlamp Leveling/mirror Control Switch" in this section.

    4. C7A19F05
    Display graphicTranslations of text in graphics


  4. Remove the I/P vent-driver. Refer to "Instrument Panel Vent-Driver" in this section.
  5. Remove the steering wheel. Refer to Section 6E. Steering Wheel and Column.
  6. Remove the headlamp/turn signal switch. Refer to Section 6E. Steering Wheel and Column.
  7. Remove the wiper switch. Refer to Section 6E. Steering Wheel and Column.
  8. Remove the instrument cluster. Refer to "Instrument Cluster" in this section.
  9. Remove the instrument panel lower compartment. Refer to "Instrument Panel Lower Compartment" in this section.

    10. C7A19E03
    Display graphicTranslations of text in graphics


  10. Remove the audio system. Refer to Section 9F, Audio Systems.
  11. Remove the sun sensor and the automatic temperature controls assembly. Refer to Section 7D, Automatic Temperature Control Heating, Ventilation, and Air Conditioning System.
  12. Remove the body control module. Refer to Section 9V. Body Control Module.
  13. Remove the instrument compartment. Refer to Instrument Compartment” in this section.
  14. Remove the I/P vent-passenger. Refer to "Instrument Panel Vent-Passenger" in this section.

    15. C7A18B07
    Display graphicTranslations of text in graphics


  15. Remove the passenger airbag securing bolts from tie bar.
  16. Remove the passenger airbag securing bolts from tie bar.

    17. C7A19E06
    Display graphicTranslations of text in graphics


  17. Remove the bolt caps and the securing bolts in both side of instrument panel below windshield.
  18. Remove the bolt caps and the securing bolts in both side of instrument panel below windshield.

    19. C8A19E04
    Display graphicTranslations of text in graphics


  19. Remove the securing bolts and nut on the left and right side of instrument panel.
  20. Remove the securing bolts and nut on the left and right side of instrument panel.

    21. C8A19E05
    Display graphicTranslations of text in graphics


  21. Remove the securing nut on right side of front console.
  22. Remove the securing nut on right side of front console.

    23. C8A19E06
    Display graphicTranslations of text in graphics


  23. In order to get access into the bolts behind the I/P cluster loosen the lower I/P from upper I/P by removing securing screws.
  24. In order to get access into the bolts behind the I/P cluster loosen the lower I/P from upper I/P by removing securing screws.

    25. C8A19E07
    Display graphicTranslations of text in graphics


  25. Pulling the lower I/P and remove the securing bolts behind the I/P cluster.
  26. Pulling the lower I/P and remove the securing bolts behind the I/P cluster.

    27. C8A19E08
    Display graphicTranslations of text in graphics


  27. Remove the screws securing the I/P center vents.
  28. Remove the screws securing the I/P center vents.

    29. C8A19E09
    Display graphicTranslations of text in graphics


  29. Remove the securing nut behind the I/P center vent-right.
  30. Remove the securing nut behind the I/P center vent-right.

    31. C7A19E08
    Display graphicTranslations of text in graphics


  31. Disconnect the guide pins from the dash panel by pulling the instrument panel assembly.
  32. Disconnect the guide pins from the dash panel by pulling the instrument panel assembly.
  33. Remove the instrument panel from the vehicle.
  34. Remove the instrument panel from the vehicle.

C7A19E08
Display graphicTranslations of text in graphics


Installation Procedure

  1. Position the instrument panel in the vehicle.

    2. Notice : Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion.


    C8A19E09
    Display graphicTranslations of text in graphics


  2. Install the securing nut behind the I/P center vent-right.

    3. Tighten
    Tighten the securing nut to 23 N•m (17 lb-ft).


    C8A19E08
    Display graphicTranslations of text in graphics


  3. Remove the I/P center vent screws.

    4. C8A19E07
    Display graphicTranslations of text in graphics


  4. Pulling the lower I/P and install the securing bolts behind the I/P cluster.

    5. Tighten
    Tighten the securing nut to 23 N•m (17 lb-ft).


    C8A19E06
    Display graphicTranslations of text in graphics


  5. Install the screws connecting the upper I/P with the lower I/P.

    6. C8A19E05
    Display graphicTranslations of text in graphics


  6. Install the securing nut on right side of front console.
  7. Install the securing nut on right side of front console.

    8. Tighten
    Tighten the securing nut to 23 N•m (17 lb-ft).


    C8A19E04
    Display graphicTranslations of text in graphics


  8. Install the securing bolts and nut on the left and right side of instrument panel.

    9. Tighten
    Tighten the securing nut to 23 N•m (17 lb-ft).


    C7A19E06
    Display graphicTranslations of text in graphics


  9. Install the securing bolts in both side of instrument panel below windshield.
  10. Install the bolt caps.

    11. C7A18B07
    Display graphicTranslations of text in graphics


  11. Install the bolts securing the passenger airbag bolts on tie bar.

    12. Tighten
    Tighten the securing nut to 10 N•m (7 lb-ft).


    C7A19E03
    Display graphicTranslations of text in graphics


  12. Install the I/P vent-passenger. Refer to "Instrument Panel Vent-Passenger" in this section.
  13. Install the instrument compartment. Refer to "Instrument Compartment” in this section.
  14. Install the body control module. Refer to Section 9V. Body Control Module.
  15. Install the sun sensor and the automatic temperature controls assembly. Refer to Section 7D, Automatic Temperature Control Heating, Ventilation, and Air Conditioning System.
  16. Install the audio system. Refer to Section 9F, Audio Systems.

    17. C7A19F05
    Display graphicTranslations of text in graphics


  17. Install the instrument panel lower compartment. Refer to "Instrument Panel Lower Compartment" in this section.
  18. Install the wiper switch. Refer to Section 6E. Steering Wheel and Column.
  19. Install the headlamp/turn signal switch. Refer to Section 6E. Steering Wheel and Column.
  20. Install the steering wheel. Refer to Section 6E. Steering Wheel and Column.
  21. Install the I/P vent-driver . Refer to "Instrument Panel Vent-Driver" in this section.

    22. C7A19E10
    Display graphicTranslations of text in graphics


  22. Install the instrument cluster dimmer/headlamp leveling/mirror control switch assembly. Refer to “Instrument Cluster Dimmer/Headlamp Leveling Mirror Control Switch” in this section.
  23. Install the front, rear floor console. Refer to Section 9G, Interior Trim.
  24. Connect the negative battery cable.

GENERAL DESCRIPTIONAND SYSTEM OPERATION

Instrument Panel Vents

The center and the side vents in the instrument panel can be adjusted up and down and from side to side. The side vents can also be aimed toward the side windows to defog them.

Instrument Compartment

The instrument compartment can be opened by pulling up on the latch handle. The instrument compartment must be removed to gain access to the passenger side airbag module, (if equipped).

Digital Clock

The digital clock is located on the instrument panel above the radio. The clock is capable of an outside temperature display and a 12-hour or a 24-hour display.

Instrument Cluster

The instrument cluster is located above the steering column and in the instrument cluster trim panel. The instrument cluster contains the instruments that provide the driver with vehicle performance information. The instrument cluster contains a speedometer, a tachometer, an odometer, a trip odometer, a temperature gauge, a fuel gauge, and several indicator lamps.

Speedometer

The speedometer measures the speed of the vehicle in km/h or mph (with km/h). It consists of an instrument cluster gauge connected to the vehicle speed sensor on the transaxle output shaft.

Trip Odometer

The trip odometer measures the distance the vehicle has traveled since it was last reset. It consists of an instrument cluster gauge connected to the sending unit on the transaxle output shaft. The trip odometer can be reset to zero at any time so that the driver can record the distance traveled from any starting point.

Fuel Gauge

The fuel gauge consists of an instrument cluster gauge connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank only when the ignition is turned to ON or ACC. When the ignition is turned to LOCK or START, the pointer may come to rest at any position.

Temperature Gauge

The temperature gauge consists of an instrument cluster gauge connected to a temperature sensor that is in contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the coolant. Prolonged driving or idling in very hot weather may cause the pointer to move beyond the center of the gauge. The engine is overheating if the pointer moves into the red zone at the upper limit of the gauge.

Tachometer

The tachometer measures the engine's speed in terms of thousands of revolutions per minute. It consists of an instrument cluster gauge connected to a sending unit in the engine control module.
Do not operate the engine in the red zone. Engine damage may occur.

Chime

The chime will sound to bring attention to one or more of the following conditions:
Voltage is supplied at all times through the fuse block to power the chime.

Driver Information Center

A Driver Informaion Center (DIC) is fitted to the instrument panel center. The DIC displays the functions of the heating and ventilation system and the trip computer. The DIC has no serviceable items. If any component fails to function, the module must be replaced.


To Previous PageTo Next Page
© Copyright Chevrolet Europe. All rights reserved