To the top of the document
Captiva
To Previous PageTo Next Page
GMDE Start PageLoad static TOCLoad dynamic TOCHelp?

SECTION 9G

INTERIOR TRIM

Caution : Disconnect the negative battery cable before removing or installing any electrical unit or when atool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cablewill help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unlessotherwise noted.

SPECIFICATIONS

Fastener Tightening Specifications

Application
N•m
Lb-Ft
Lb-In
Windshield Garnish Molding Screw
2
-
18
Center Pillar Lower Garnish Molding Screw
22
16
-
Quarter Window Garnish Molding Screw
2
-
18
Floor Console Bolts
8
-
71
Front Console Retainer Screw
2
-
18
Hood Latch Release Handle Mounting Screw
3
-
27
Rear Compartment Stow Tray Bolts
8
-
71
Rear Wheelhouse Trim Panel Screws
2
-
18
Driver Knee Bolster Screws
2.5
-
23
Driver Knee Bolster Bolts
20
15
-

SPECIAL TOOLS

Special Tools Table


KM475B
Display graphicTranslations of text in graphics


KM-475-B
Trim Remover

MAINTENANCE AND REPAIR

ON-VEHICLE SERVICE


C7A19G01
Display graphicTranslations of text in graphics


Windshield Garnish Molding

Removal Procedure

  1. Remove the bolt and the windshield garnish molding.

C7A19G01
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the windshield garnish molding with the bolt.
  2. Install the windshield garnish molding with the bolt.

    3. Tighten
    Tighten the windshield garnish molding bolt to 2 N•m (18 lb-in).


C7A19G03
Display graphicTranslations of text in graphics


Center Pillar Lower Garnish Molding

Removal Procedure

  1. Reposition the rear portion of the front side door retainer and the front portion of the rear side door retainer.
  2. Remove the center pillar lower garnish molding.

C7A19G03
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the center pillar lower garnish molding.
  2. Install the front side door retainer and the rear side door retainer to their original positions.

C7A19G02
Display graphicTranslations of text in graphics


Center Pillar Upper Garnish Molding

Removal Procedure

  1. Remove the bolt and the upper front seat belt anchor.
  2. Reposition the upper portion of the center pillar lower garnish molding.
  3. Remove the screw and pry off the center pillar upper garnish molding.

C7A19G02
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the center pillar upper garnish molding.
  2. Install the center pillar upper garnish molding.

    3. Tighten
    Tighten the center pillar upper ganish molding screw to 22 N•m (16 lb-ft).

  3. Install the upper portion of the center pillar lower garnish molding.
  4. Install the upper front seat belt anchor with the bolt.

    5. Tighten
    Tighten the seat belt anchor bolt to 38 N•m (28 lb-ft).


C7A19G06
Display graphicTranslations of text in graphics


Quarter Window Garnish Molding

Removal Procedure

  1. Remove the rear seat lower belts. Refer to Section 8A, Seat Belts.
  2. Remove the screws and the quarter window garnish molding.

C7A19G06
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the quarter window garnish molding with the screws.

    2. Tighten
    Tighten the quarter window garnish molding screws to 2 N•m (18 lb-in).

  2. Install the rear seat lower belts. Refer to Section 8A, Seat Belts.

C7A19G04
Display graphicTranslations of text in graphics


Front Side Door Retainer

Removal Procedure

  1. Remove the front side door retainer.

C7A19G04
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the front side door retainer.

C7A19G05
Display graphicTranslations of text in graphics


Rear Side Door Retainer

Removal Procedure

  1. Remove the rear side door retainer.

C7A19G05
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear side door retainer.

C7A19G10
Display graphicTranslations of text in graphics


Floor Panel Rear Extension

Removal Procedure

  1. Remove the floor panel rear extension.

C7A19G10
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the floor panel rear extension.

C7A19G07
Display graphicTranslations of text in graphics


Floor Console

Tools Required

KM-475-B Trim Remover

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the instrument compartment, instrument panel lower cover, audio system.
  3. Remove the screws and cup holder, console cover.

    4. C7A19G08
    Display graphicTranslations of text in graphics


  4. Disconnet the electrical connector.
  5. Remove the bolts from the floor console.
  6. Remove the floor console.

    7. C7A19G09
    Display graphicTranslations of text in graphics


  7. Remove the screws from the front console retainer.

C7A19G09
Display graphicTranslations of text in graphics


Installation Procedure

  1. Connect the electrical connectors.
  2. Install the front console retainer with screws.

    3. Tighten
    Tighten the front console retainer screws to 8 N•m (71 lb-in).

  3. Install the floor console with the bolts.

    4. Tighten
    Tighten the floor console screw to 8 N•m (71 lb-in).


    C7A19G08
    Display graphicTranslations of text in graphics


  4. Connect the electrical connectors.
  5. Install the cupholder and console cover.

    6. C7A19G07
    Display graphicTranslations of text in graphics


  6. Install the instrument compartment, instrument panel lower cover, audio system.
  7. Connect the negative battery cable.

C7A18A02
Display graphicTranslations of text in graphics


Floor Carpet

Removal Procedure

  1. Disconnect the negative battery cable.
  2. Remove the rear seat cushion. Refer to Section 9H,Seats.
  3. Remove the left and the right rear side door retainer. Refer to "Rear Side Door Retainer" in this section.
  4. Remove the bolts and the left and the right lower front seat belt anchors from the center pillar garnish molding.

    5. C7A19G14
    Display graphicTranslations of text in graphics


  5. Remove the left and the right front side door retainer.
  6. Remove the left and the right center pillar lower garnish molding. Refer to "Center Pillar Lower Garnish Molding" in this section.
  7. Remove the front seats. Refer to Section 9H,Seats.
  8. Remove the floor console. Refer to "Floor Console" in this section.
  9. Remove the gearshift housing bolts and reposition the gearshift housing.

    10. C7A19G11
    Display graphicTranslations of text in graphics


  10. Remove the floor carpet retaining clips.
  11. Remove the floor carpet.

C7A19G11
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the floor carpet.
  2. Install the floor carpet retaining clips.

    3. C7A19G14
    Display graphicTranslations of text in graphics


  3. Install the gearshift housing with the bolts.

    4. Tighten
    Tighten the gearshift housing bolts to 8N•m (70lb-in).


    C7A18A02
    Display graphicTranslations of text in graphics


  4. Install the floor console. Refer to "Floor Console" in this section.
  5. Install the front seats. Refer to Section 9H,Seats.
  6. Remove the left and the right center pillar lower garnish molding. Refer to "Center Pillar Lower Garnish Molding" in this section.
  7. Install the left and the right front side door retainer.
  8. Install the left and the right lower front seat belt anchors to the ceter pillar garnish molding with the bolts.

    9. Tighten
    Tighten the seat belt anchor bolts to 38 N•m (28 lb-ft).

  9. Install the left and the right rear side door retainer. Refer to "Rear Side Door Retainer" in this section.
  10. Install the rear seat cushion. Refer to Section 9H,Seats.
  11. Connect the negative battery cable.

C7A19G12
Display graphicTranslations of text in graphics


Rear Compartment Stow Tray

Removal Procedure

  1. Remove the bolts and the rear compartment stow tray.

C7A19G12
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear compartment stow tray with the bolts.

    2. Tighten
    Tighten the rear compartment stow tray bolts to 8 N•m (11 lb-ft).


C7A19G13
Display graphicTranslations of text in graphics


Rear Wheelhouse Trim Panel

Removal Procedure

  1. Remove the rear seat lower bolts. Refer to Section 8A, Seat Belts.
  2. Remove the rear compartment stow tray. Refer to "Rear Compartment Stow Tray" in this section.
  3. Remove the screws and the rear wheelhouse trim panel.

C7A19G13
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the rear wheelhouse trim panel with the screws.

    2. Tighten
    Tighten the rear wheelhouse trim panel screws to 2 N•m (18 lb-in).

  2. Install the rear compartment stow tray. Refer to "Rear Compartment Stow Tray" in this section.
  3. Install the rear seat lower bolts. Refer to Section 8A, Seat Belts.

C7A19G15
Display graphicTranslations of text in graphics


Driver Knee Bolster

Removal Procedure

  1. Remove the instrument panel steering colum opening pillar. Refer to Section 9E, Instrumentation/Driver Information.
  2. Remove the screws and bolts.
  3. Remove the driver knee bolster.

C7A19G15
Display graphicTranslations of text in graphics


Installation Procedure

  1. Install the driver knee bolster with the screws and bolts.

    2. Tighten
    Tighten the driver knee bolster screws to 2.5 N•m (23 lb-in).
    Tighten the driver knee bolster bolts to 20 N•m (15 lb-ft).

  2. Install the instrument panel steering column opening pillar. Refer to Section 9E, Instrumentation/Driver Information.

GENERAL DESCRIPTIONAND SYSTEM OPERATION

Interior Trim Panels

The interior trim panels are molded plastic and fasten with screws or plastic clips.

Pressure Relief Vent

When all the windows are closed and the ventilation system is on, the addition of outside air to the interior of the vehicle causes a positive pressure within the vehicle. To relieve the pressure, air is released through a pressure relief vent. The pressure relief vents are located at the rear quarter of the vehicle, behind the bumper fascia.

Floor Console

The floor console fits over the tunnel in the floor of the vehicle and extends from under the center of the instrument panel to the rear seat area. The front portion of the console contains the cigar lighter and the transaxle shift lever. The rear portion of the console contains the parking brake lever, a cupholder, a storage compartment, and an ashtray for the rear seat occupants.
The sensing and diagnostic module (SDM) for the airbag system and the remote keyless entry module are located under the console.

Floor Carpet

The one-piece floor carpet goes over both the front and the rear floor pans.


To Previous PageTo Next Page
© Copyright Chevrolet Europe. All rights reserved