To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

DTC P0496

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    • Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0496: Evaporative Emission (EVAP) System Flow During Non-Purge

Circuit/System Description

This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP purge solenoid valve OFF and the EVAP vent solenoid valve ON. The engine control module (ECM) monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.

The following table illustrates the relationship between the ON and OFF states, and the Open or Closed states of the EVAP purge and vent solenoid valves.

Control Module Command

EVAP Purge Solenoid Valve

EVAP Vent Solenoid Valve

ON

Open

Closed

OFF

Closed

Open

Conditions for Running the DTC

    • DTCs P00C8, P00C9, P0068, P16F3, P0106, P0107, P0108, P0111, P0112, P0113, P0114, P0116, P0117, P0118, P0122, P0123, P0125, P0128, P160E, P160D, P0191, P0192, P0193, P0222, P0223, P0443, P0449, P0452, P0453, P0454, P0502, P0503, P0606, P0722, P0723, P1104, P2100, P2101, P2102, P2103, P2135, P2227, P2228, P2229, P2230 are not set
    • The ignition voltage is between 11-32 V.
    • The barometric pressure (BARO) is greater than 70 kPa.
    • The fuel level is between 10-90 %.
    • The start-up engine coolant temperature (ECT) is less than 35°C (95°F).
    • The start-up intake air temperature (IAT) is between 4-30°C (39-86°F).
    • DTC P0496 runs once per cold start for maximum of 17 min.

Conditions for Setting the DTC

The control module detects vacuum during a non-purge condition for a predetermined time.

Action Taken When the DTC Sets

DTC P0496 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0496 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Evaporative Emission Control System Description

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

  1. Ignition ON, engine OFF.
  2. Seal the EVAP system using the Purge/Seal function with a scan tool.
  3. Start the engine.
  4. Observe the FTP sensor with a scan tool. The Fuel Tank Pressure Sensor parameter should be less than 1.7 V after 90 s.
  5. If the Fuel Tank Pressure Sensor parameter is greater than the specified range, replace the Q12 evaporative emission purge solenoid valve.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Evaporative Emission Canister Purge Solenoid Valve Replacement : LE5 or LE9 → LD9

   


© Copyright Chevrolet. All rights reserved