To the top of the document
Captiva
   
GMDE Start Page Load static TOC Load dynamic TOC Help?

Camshaft Replacement - Left Side

Special Tools

    • EN-46108 Timing Chain Retention Tool
    • EN-46111 Crankshaft Rotation Socket

For equivalent regional tools, refer to Special Tools .

Removal Procedure

  1. Remove the intake manifold. Refer to Inlet Manifold Replacement .
  2. Remove the left bank camshaft cover. Refer to Camshaft Cover Replacement - Left Side .
  3. Remove the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust and Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake .
  4. Remove the camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake .
  5. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement .

  6. 1306293
  7. Rotate the crankshaft with the EN-46111 socket until the camshafts are in a neutral (low tension) position. The camshaft flats will be parallel with the camshaft cover rail (1).
  8. Caution: Refer to Torque Reaction Against Timing Drive Chain Caution in the Preface section.


    1340931

    Note: 

       • Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.
       • DO NOT remove the camshaft position actuator bolt at this time.

  9. Loosen the camshaft position actuator bolt.
  10. Note: Ensure that the tips of the EN-46108 tool are fully engaged into the timing chain (3 and 4).


    1341287
  11. Install the EN-46108 tool (1 and 2) in order to retain the timing chain.
  12. Firmly tighten the EN-46108 tool nuts.


    1306391

    Note: Ensure that the camshaft timing chain and the camshaft position actuators are marked for proper assembly.

  13. Mark the timing chain and the respective locations on the camshaft position actuators (1-4).
  14. Remove the camshaft position actuator bolt.
  15. Remove the camshafts. Refer to Camshaft Removal - Left Side .

Installation Procedure


    1306391

    Note: 

       • Ensure that the marks on the camshaft position actuator and the timing chain (1-4) are aligned.
       • DO NOT tighten the camshaft position actuator bolt at this time.

  1. Locate the camshafts to the cylinder head and assemble the camshaft actuators to the camshafts.
  2. Install the camshafts and the camshaft bearing caps. Refer to Camshaft Installation - Left Side .
  3. Remove the EN-46108 tool .
  4. Caution: Refer to Torque Reaction Against Timing Drive Chain Caution in the Preface section.


    1340931

    Note: Use an open-end wrench at the camshaft hex to prevent camshaft/engine rotation.

  5. Install and tighten the camshaft position actuators. Refer to Camshaft Position Actuator Installation - Left Side Inlet and Camshaft Position Actuator Installation - Left Side Exhaust .
  6. Install the intake camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake .
  7. Install the camshaft sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust and Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake .
  8. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement .
  9. Install the camshaft cover. Refer to Camshaft Cover Replacement - Left Side .
  10. Install the inlet manifold. Refer to Inlet Manifold Replacement .
   


© Copyright Chevrolet. All rights reserved